- Home
- Conferences
- Conference Proceedings
- Conferences
19th International Petroleum and Natural Gas Congress and Exhibition of Turkey
- Conference date: 15 May 2013 - 17 May 2013
- Location: Ankara, Turkey
- Published: 15 May 2013
1 - 100 of 144 results
-
-
Locating near-surface scatterers by seismic interferometry of scattered surface waves: Investigating the effect of an offline cavity
Authors N. Bulut, U. Harmankaya and A. KaslilarA recently developed method based on active-source seismic interferometry and inversion is used to find the location of an offline (out of plane) near-surface scatterer. In the method a 2D geometry has been considered and the interferometric estimates of the scattered surface waves have been obtained for different locations of virtual sources. The interferometric traveltimes of these scattered surface waves were used in inversion to find the location of the scatterer. It has been shown that only one source at the surface is sufficient to successfully obtain the location of an inline scatterer. In this study an offline scatterer, a cavity, is considered to understand the effects of a 3D medium in estimating the location of the scatterer using the method. As expected, the location of the offline scatterer is estimated with some error when 2D geometry and related formulas are considered. In case of inline shot profiles, one should consider the possibility of an offline scatterer and be aware that the estimations of location can be effected by the existence of an offline catterer and cause misinterpretations.
-
-
-
Doğu Karadeniz’de Gaz Hidratların ve Sığ Gaz Birikimlerinin Akustik Özellikleri ile ilgili Yapılan AVO Analizi
More LessSon zamanlarda, gaz hidrat ve hidrata bağlı sığ gaz araştırmalarının önemi gün geçtikçe artmaktadır. Karadeniz de, 100-120m derinliğinde anoksik bir ortam mevcuttur. Ayrıca gaz konsantrasyonu nedeni ile derin yapılardan sıvı göçü, çamur volkanı gelişimi ve deniz tabanına gaz sızıntıları bakımından oldukça yüksek potansiyele sahiptir. Karadeniz’in sahip olduğu kalın tortul örtüsü ve buna ek olarak Arap ve Avrupa kıtalarının Eosen zamanından bu yana çarpışması ile Karadeniz kıyı sınırlarında gelişen sıkışmalı deformasyon nedeni ile aşırı basınç etkisi altında kalan sıvıların faylar aracılığıyla yukarıya doğru göçüne neden olmaktadır. Doğu Karadeniz’deki deniz sismik çalışmaları, Deniz Bilimleri ve Teknolojisi Enstitüsü (DBTE) Sismik Laboratuvarı (SEİSLAB) ve Pukyong Ulusal Üniversitesi›nin (PKNU) hem teknik hem de bilimsel dayanışmasıyla gerçekleştirilmiştir. Doğu Karadeniz’de belirtilen alanlarda sığ gaz ve gaz hidrat oluşumları, çeşitli hidrokarbon sızıntıları (pockmark, çamur volkanları, sızıntıya neden olan faylar) haritalanarak, tortulların hem fiziksel hem de akustik özellikleri incelenmiştir. Çalışma alanında kıtasal yamaç, apron ve abisal düzlük yer almaktadır. Aynı zamanda alanın doğusundaki sismik kesitlerde BSR, parlak nokta (bright spot) ve gaz kolonları gözlenmiştir. Sismik kesitlerde iki adet çamur volkanı belirlenmiş olup bunlar, İzmir ve Pusan olarak adlandırılmıştır. Sismik kesitlerde kıtasal yamaçta kayma çökelleri gözlenmiştir. Gözlenen akustik saydam bölgeler tortullardaki olası gazın varlığını işaret ederken bu maskelenmelerin etrafında gözlenen yüksek genlikli ve ters polariteli yansımların da bunu doğruladığı düşünülmektedir. Bu durum da alandaki gaz birikiminin varlığını desteklemektedir. Elde edilen sonuçların ışığında, gaz birikimleri; AVO analizlerinden elde edilen gradyentler ve grafiklerle yapılan çapraz-korelasyon sonucunda belirlenmiş ve bunun birinci sınıf AVO anomalisi olduğu gözlenmiştir. Anahtar Kelimeler: Doğu Karadeniz, Gaz Hidrat, BSR, Parlak Nokta, Fiziksel ve Akustik Özellikler, Çok Kanallı Sismik Yansıma, Sismik Özellik, AVO.
-
-
-
Boşluk Basıncının ve Sıcaklığın Sismik Hızlar Üzerine Etkileri Pore Pressure and Temperature Effects on the Seismic Velocities
By O. GüreliRezervuar içindeki sıvının fiziksel özelliklerinin ve miktarının belirlenmesinde, sismik analizin önemli bir kısmı (AVO, 4D gibi) sıvının durumu ile ilgilidir. Rezervuar içindeki sıvının belirlenme amacı, belirlenmiş bir rezervuarın durumu (basınç, sıcaklık, porozite, mineral tipi ve su tuzluluğu gibi) ve boşluk içindeki sıvının %100 su, hidrokarbon veya gaz ile dolu olması durumunun sismik hızlar ve yoğunluk ile modellenmesidir. Gözenek içindeki sıvılar kayaçların sismik özelliklerini çok güçlü bir şekilde etkiler. Boşluk sıvılarının yoğunlukları, bulk modülü, hızları ve viskoziteleri jeofizikte genellikle çok basitleştirilir. Aslında kayacın fiziksel özellikleri çok karmaşıktır. Ampirik bağıntılar ile sismik ara hızlardan boşluk içindeki sıvının basıncı elde edilebilir. Sismik hızlar kullanılarak da düşük ve yüksek sıcaklıklı ve basınçlı yerler elde edilebilir.
-
-
-
A Field Application of Lumped Parameter Models
By H. SarakThis paper deals with the application of lumped parameter models (1-tank, 2-tank open/closed, 3-tank open/closed) to the long-term observed pressure behavior of Hofsstadir geothermal field which is a typical low-temperature liquid dominated geothermal system, in West Iceland. Once the model parameters of the tank models are determined by history matching, then future performance predictions are made under given production/reinjection scenarios by using the Randomized Maximum Likelihood method.
-
-
-
Dünden Bugüne Balçova-Narlidere Jeotermal Sahası
By T. SayıkBalçova - Narlıdere Jeotermal Sahası, Türkiye’de jeotermal enerjiden daha verimli ve daha ileri düzeyde faydalanmak amacıyla, bilimsel çalışmaların başlatıldığı ilk sahadır. Sahada 1960’lı yılların başında, bir dizi jeolojik ve jeofizik etüt çalışmasının ardından, 1963 yılında jeotermal enerji elde etmek ve sahanın potansiyelini belirleyebilmek için, MTA tarafından sığ jeotermal kuyuların delinmesine başlanmıştır. 80’li yılların başına kadar devam eden saha tanımlama ve kısmi üretim uygulamalarının ardından, 1983 yılında «B» kodlu sığ jeotermal üretim kuyularının delinmesine başlanmıştır. Tüm bu çalışmalar MTA tarafından yürütülmüş olup, elde edilen veriler güncel çalışmalara da ışık tutmaktadır. Yaklaşık 50 yıldır, bilimsel çalışmaların aralıksız sürdürüldüğü bu sahada, şu an itibariyle kullanılan 4 Sığ, 10 Derin jeotermal kuyudan üretim yapılmakta ve 4 re-enjeksiyon kuyusundan da (BD-3, BD-8, BD-10, BD-15), jeotermal sistemi ve rezervuarı korumak amacıyla, enerjisi alınmış olan jeotermal akışkan geriye basılmaktadır. Balçova Jeotermal Enerji Merkezi Isıtma Sistemi’nin kurulum çalışmalarına, 1983 yılında Balçova Termal Otel Tesisleri’nin kuyu içi eşanjörü ile ısıtılmasıyla başlanmıştır. Bunun ardından, aynı sene içerisinde Dokuz Eylül Üniversitesi Uygulama ve Araştırma Hastanesi de kuyu içi eşanjör sistemiyle ısıtılmaya başlanmış ve böylelikle, bugün yaklaşık 30.000 KE kurulu kapasiteye ulaşmış olan bölge ısıtma sisteminin ilk adımları atılmıştır. Sistemin güncel kapasitesi yaklaşık 160 MWt gücünde 3.000.000 m² kapalı alan (30.500 KE fiili) ısıtma kapasitesi olan “dünyanın en büyük, jeotermal kaynaklı bölge ısıtma” sistemlerinden biridir. Sistemin temel bileşenleri, kuyular (üretimreenjeksiyon- gözlem), boru (isale) hatları, ısı merkezleri ve pompa istasyonlarıdır. Mevcut sistemde, 14 adet Üretim Kuyusu, 4 adet Re-enjeksiyon Kuyusu, 4 adet Gözlem Kuyusu, yaklaşık 400 km boru hattı, 9 adet Isı Merkezi, 2 adet Alt Isı Merkezi, 2 adet Pompa (Terfi) İstasyonu bulunmaktadır. Bunlara ek olarak, tüm bu bileşenlerin senkronize çalışmasını sağlayabilmek ve sistemin genelini tek bir merkezden kontrol edebilmek için, otomasyon sistemi kurulum çalışmaları hızla devam etmektedir. Bu sistem tam anlamıyla devreye alındığında, tüm kuyular ve ısı merkezleri uzaktan algılama yöntemiyle izlenebilecek, gereken müdahaleler eş zamanlı olarak yapılabilecektir. Bu bildiride, Balçova sahasında 16 yıldır (1996 – 2012) sürdürülen jeotermal kaynaklı merkezi ısıtma uygulaması tecrübesi aktarılacaktır. Uygulama sürecinde karşılaşılan dağıtım hattı sorunları (korozyon, akışkan kaçakları) ve çözüm yolları, rezervuar basınç ve sıcaklığında görülen düşümler ve bu düşümler konusunda alınan tedbirler ve bu tedbirlere sahanın verdiği tepkiler tartışılacaktır. Böylesi bir sistemin temel bileşenlerinden olan kullanıcı (abone) alışkanlıkları, bu alışkanlıkları enerji kullanımına ve sonunda rezervuarın sürdürülebilirliğine olan etkileri irdelenecektir.
-
-
-
TPAO Trakya Sahası Petrol Ve Doğalgaz Üretim Atıksularının Karakterizasyonu Ve Arıtılması
Authors E.E. TOKOĞLU, S. Sayili, P. Hoşhan, Ş.D. Atay, İ. Koyuncu, C. Kinaci, M. Altinbaş, H. Özgün, M.E. Erşahín, B. Atay, S. Erdem, M. Altinbaş, B. Köse and R. KayaTPAO tarafından, petrol ve doğalgaz üretim faaliyetleri sonucu oluşan atıksular olumsuz çevresel etkilerin önlenmesi amacı ile yeraltına enjeksiyon yöntemi ile bertaraf edilmekte olup, nihai deşarjın enjeksiyon kuyusuna yapılamadığı durumlar için (jeolojik formasyonun uygun olmaması, kapasitesinin yetmemesi, yeni kuyu bulunamaması vb.), üretim atıksuyunun uzaklaştırılması ve ilgili deşarj standartlarının sağlanması konusunda uygulamaya yönelik alternatifler oluşturmak amacı ile teknik çalışmalar yürütülmekte ve yeni projeler geliştirilmektedir. Bu kapsamdaki çalışmalardan biri 107G091 numaralı, İstanbul Teknik Üniversitesi (İTÜ) ve TPAO Araştırma Merkezi ortaklığında yürütülen, “Petrol ve Doğalgaz Üretim Faaliyetleri Sonucu Oluşan Atıksuların Yönetimi” başlıklı projesidir. TPAO Genel Müdürlüğü’ne bağlı Trakya Bölge Müdürlüğü bünyesindeki üretim sahalarında oluşan petrol ve doğalgaz üretim atıksuları için en verimli ve ekonomik arıtma sisteminin geliştirilmesi ve uygulanması amacı ile uygulamaya konulan projede, atıksu karakterizasyonu çalışmaları sonrasında, çeşitli arıtma metotları karşılaştırılarak, arıtma performansına bağlı olarak uygun nihai deşarj alternatifleri belirlenmeye çalışılmış ve Trakya Bölgesi’ne göre modeller oluşturulmuştur. Proje kapsamında üretimi yıl boyunca devam eden 10 adet petrol ve doğal gaz sahasından alınan atıksuların karakterizasyonu yapılmış ve Su Kirliliği Kontrolü Yönetmeliği (SKKY)’nde adı geçen parametreler bir yıl boyunca takip edilmiştir. Çevresel açıdan büyük önem arz eden pH, iletkenlik, tuzluluk, toplam çözünmüş katı madde (TÇM), askıda katı madde (AKM), kimyasal oksijen ihtiyacı (KOİ), yağ ve gres, fenol, toplam petrol hidrokarbonları (TPH), toplam Kjeldahl Azotu (TKN), ağır metaller, ana ve eser elementler aylık bazda düzenli olarak incelenmiştir. AKM, pH, sülfat, civa, kurşun, kadmiyum, çinko, bakır, krom ve demir parametreleri SKKY Standartlarına göre kabul edilebilir düzeyde iken arıtmanın gerekli olduğu parametreler amonyum azotu, KOİ, yağ ve gres, sülfür, sodyum, TPH olarak belirlenmiştir. Bu çalışmada örnek teşkil edecek bir petrol, bir doğal gaz ve bir petrol+ doğal gaz sahası seçilmiş ve yıl boyunca elde edilen değerlerin ortalamaları Tablo 1’de gösterilmiştir. Atıksu karakterizasyonu ile birlikte laboratuvar ölçekli çalışmalarda sahalara göre atıksular ayrı ayrı ve karıştırılarak belirlenen proseslerden geçirilerekarıtılabilirlik çalışmaları yürütülmüştür. Bu kapsamda membran proses (MBR), mikrofiltrasyon (MF), ultrafiltrasyon (UF) sistemleri ön arıtma prosesleri olarak, aktif karbon ve ters osmoz sistemleri ileri arıtma prosesleri olarak denenmiştir. Yapılan denemeler sonucunda, uygun arıtma yöntemine karar verilmiş ve ön arıtma, ön filtrasyon, ileri arıtma ünitesi ile yardımcı ekipmanlar ve tanklardan oluşan, scada sistemi ile kontrol edilen 5m3/gün debiye sahip pilot ölçekli sistem kurulumu gerçekleştirilmiştir (Şekil-1). Bu pilot tesis ile yaklaşık 1 yıl süresince yerinde arıtılabilirlik çalışmaları yapılmıştır.
-
-
-
Sondaj Atıksuları Yönetimi ve Geri Kazanımı
Authors B. EKİZER, N. Köse and E. BuzpinarHızla artan dünya nüfüsuna paralel olarak insanoğlunun yakıt ihtiyacında da artış meydana gelmekte, bu da dünyada petrol ve doğalgaz sondajlarının sayılarının her geçen gün artmasına sebep olmaktadır. Sözkonusu sondaj faaliyetlerinin artması beraberinde sondaj faaliyetleri sırasında ortaya çıkan atıklardan kaynaklanan çevre kirliliği sorunlarının artmasına sebep olması nedeniyle TPAO(Türkiye Petrolleri A.O) gibi hidrokarbon sondajı yapan şirketleri sondaj atıklarının bertarafı konusunda yeni yöntemleri araştırma ve geliştirmeye yöneltmiştir. Sondaj faaliyeti sırasında ortaya çıkan atıklardan en önemlisi sondaj çamuru atıklarıdır. Sondaj çamuru, sondaj faaliyeti sırasında kesilen zemin yapılarının yer yüzüne taşınmasını sağlamak ve diğer özel amaçlar için kullanılan özel bir sıvıdır. Sondaj çamurunun hazırlanması esnasında, fiziksel ve kimyasal özelliklerini kontrol altında tutmak için, çok çeşitli organik, inorganik ve antibakteriyel kimyasal maddeler kullanılmaktadır. Sondaj çamuru kesilen zemin parçaları ile karışık olarak yüzeye alınmakta, kesintiler fiziksel olarak ayrılarak atılmaktadır. Kesintilerin çamurdan başarılı bir şekilde ayrılması halinde sondaj çamuru ve kesintiler ayrı atıklar olarak depolanabilir. TPAO’da, atık sondaj çamuru bertaraf yöntemleri olarak, dünyada uluslararası alanda faaliyet gösteren petrol şirketlerinde de yaygın olarak kullanılan yerinde buharlaştırma, enjeksiyon ve arıtma teknolojileri uygulamaları yapılmaktadır. Genellikle arıtma teknolojileri sondaj atıksuyunun geri kazanım ile yeniden kullanılmasını sağlaması nedeniyle diğer bertaraf yöntemlerine göre avantajlı olmaktadır. TPAO İGÇ(İş Güvenliği Çevre) biriminin kontrolünde sondaj lokasyonlarında pilot ölçekli olarak kullanılmaya başlanan; Helezonik konveyör yardımı ile katı-sıvı faz ayrımı gerçekleştirildiği ve Kimyasal Karıştırma Tankı, Filtre Pres ve Su Depolama Tankı ünitelerinden oluşan Mobil Atıksu arıtma Sistemi ile de yaklaşık olarak günlük 15 ton su arıtıldığı çalışmalarla ortaya konmuştur. TPAO’da pilot ölçekli olarak gerçekleştirilen saha uygulamaları sonucunda Arıtma Sistemi çıkış suyunda, yeniden kullanıma uygun olacak şekilde; KOI, Askıda Katı Madde (AKM), Yağ-gres, Na, Fe ve Sülfür paremetrelerinde %87,5-%99,5 oranında arıtma verimi elde edilmiştir. Aynı zamanda sözkonusu çıkış suyu parametreleri Su Kirliliği Kontrol Yönetmeliği’nde belirtilen sınır değerlerin (SKKY Tablo:11.03) altında kaldığı görülmüştür.
-
-
-
Simulation of Possible Oil Spills in İskenderun Bay and the Eastern Mediterranean Between Anatolia and Cyprus
Authors M. Chilongo, K. Guliyev and I. DurgutIn this study, simulations of a possible oil spill events in the Gulf of İskenderun and the Eastern Mediterranean between Anatolia and Cyprus were performed in order to estimate the fate and behavior of spilled oil in marine environment and to assess impact of the spills. The simulations were carried out by SINTEF Marine Environmental Modeling Workbench (MEMW) or specifically its Oil Spill Contingency And Response modeling tool known as OSCAR[1].
-
-
-
Leadership and Accountability for Health and Safety
By B. İNANÇDespite significant improvements in safety performance of oil and gas industry, major accidents are still continue to occur. Human factors are the root cause of many accidents. Achieving a positive health and safety culture in an organisation is fundamental to managing health and safety effectively. The attitudes and decisions of senior managers are critical in setting the priorities of the organisation, therefore hands-on leadership is key in all cultures. Senior managers’ role is not simply restricted to directing work and monitoring compliance with rules and regulations. They should act as leaders and facilitiators: they must encourage suggestions, motivate their staff and engage with the workforce to solve health and safety problems. They should make sure that health and safety is not viewed as a separate function, but as an integral part of productivity, competitiveness and profitability and that health and safety risks are recognised as part of business. Since senior managers influence the health and safety culture in the organisation, they must lead by example. Health and safety must be on the agenda at every board or management meeting. Health and safety performance is an important element of performance reviews, and managers are accountable for the health and safety performance of their departments. Long term goals for the control of major hazards and health and safety must be set as done for financial and production goals. Senior managers should meet the workforce regularly and discuss health and safety with them, and they should ensure that individuals who raise issues or make suggestions are provided with positive feedback on their contribution and are informed personally of the actions taken as a result of their input. Contracts should be awarded to companies which demonstrate a good health and safety performance. Senior managers should meet regularly with the managers of the contractors to review their health and safety performnce against clearly defined expectations. All incidents and near misses should be investigated fully to identify the underlying causes and follow up on the agreed actions, and senior managers must ensure that the investigation procedure consider all issues, including humann factors, and immediate as well as underlying management-related causes are identified without attributing blame and that corrective actions are taken to prevent the incident happening again. All the leadership issues mentioned here will be explained with working examples from Botas International Limited which is the BTC Pipeline Operator in Turkey and from other national&international sources.
-
-
-
Work Accidents Risk Perception Efficiency -A Case Study Approach Based on AHP Method
Authors F. Geyik and Z. EmirhanTPAO, Turkiye’s sole national oil company, has undertaken lots of oil and natural gas exploration projects both onshore and offshore, as part of its mission to develop domestic and international resources and meet the continuously increasing demand for oil and gas in Turkiye. Increasing exploration and drilling activities have proved that HSE importance also increases for the sake of those increased activities. TPAO HSE policy emphasizes applying effective risk management by defining dangerous situations and acts regarding Occupational Safety and Environmental Protection. HSE supervisors need to deal with dangers, risks, and uncertainties in a well-organized way that is different than traditional way, so as to eliminate or mitigate the risks to the acceptable levels. TPAO risk studies include the periodic audits conducted for detection of risks, the root cause analyses made after every accident, determining hazards, and detecting unsafe ambience and actions. Risks need to be perceived by all employees who can be affected by their results. At that point, companies cannot reduce accidents or prevent their workers being exposed to job illnesses unless only preparing risk analysis but also make their employees perceive risks. In this study, the relationships between real accident risks and assumed ones were investigated over case studies under the scale of HSE risk perception efficiency for using AHP method by HSE specialists. As a result, Turkish Petroleum Cooperation HSE specialists’ risk perception efficiency was evaluated and analyzed, and some useful advices were suggested. Keywords: Oil and Gas, Risk, Perception, Efficiency, Accident, AHP.
-
-
-
Petrol, Yenilenebilir Enerji ve Karbon Ayak izi Üçgeni’nde Türkiye
By O. TekeEnerji bir toplumun refahı ile doğrudan ilişkilidir. Sürekli artan enerji talebi ülkeleri enerji kaynaklarının kullanımı bakımından adeta bir yarışın içine sokmuştur. Fosil kaynaklı yakıt rezervlerin belli bir süre içinde biteceği tahmin edildiğinden bu yarışta ülkeler yenilenebilir enerji yatırımlarına önem vermeye başlamışlardır. Fosil yakıtların halen birincil enerji tüketiminde ilk sırada olması başka bir tehlike olan “Küresel Isınma” yı tetiklemektedir. Salınan sera gazlarının miktarı arttıkça dünya daha fazla ısınmakta ve tehlike büyümektedir. Türkiye Kyoto Protokolü’ ne taraf olmuş ve sera gazı azaltım yükümlülüğü altına girmiştir, fakat enerjisinin büyük bir kısmını fosil kaynaklı yakıtlardan sağladığı için çok büyük bir ilerleme sağlanamamıştır. Ayrıca yenilenebilir enerji yatırımlarının da yeterli olmaması sebebiyle istenen başarı elde edilememiştir. Çalışmanın ilk bölümünde Türkiye’ nin petrol ile ilgili aramaüretim- tüketim faaliyetleri incelenmiş olup diğer bölümde yenilenebilir enerjinin mevcut durumu incelenmiş, bu kaynakların karbon salınımları hakkında bilgi verilmiştir. Üçüncü bölümde ise karbon ayak izinden bahsedilmiş ve Türkiye’ nin karbon ayak izi hakkında bilgiler verilmiştir. Sonuç bölümünde ise çalışmanın sonuçları irdelenmiş ve bazı iyileştirme önerileri sunulmuştur.
-
-
-
How to consolidate Turkish R&D for a sustainable energy policy
Authors I. Gökalp and S.Ö. ErdoganFossil fuels, both liquid and gaseous but also solids, will remain the major energy resources all over the world for the coming decades. Turkey has a peculiar position in this area as it imports most of its petroleum and natural gas needs, possessing only significant lignite reserves. Furthermore, Turkey not only imports most of the major parts of energy conversion technologies but also oil and natural gas wells drilling technologies. Energy related imports, both in terms of fuels and related technologies constitute the main cause of Turkey’s commercial budget deficit which is prone to continue to increase if no drastic changes happen. In such a situation the main routes for changes are not many. One route is obviously the reduction of energy consumption, but in a developing country with increasing population this route is of limited impact. The second route is import substitution using domestic resources and also domestic technology. Finally, another route is hybridization of fossil fuel based energy conversion technologies with those based on renewable energy resources, such as solar and biomass for Turkey. In this paper we shall mainly focus on these two last routes. It is obvious that both options are heavily based on innovation and therefore on R&D and additionally on university and industry partnership. The paper is structured in two parts. The first part presents some examples of recent developments taken from France which also lacks fossil fuel resources. The second part highlights some recent developments in Turkey and proposes additional suggestions to strengthen them.
-
-
-
Seismic attribute analysis for gas content and structural interpretation in the Karamursel Basin, gulf of Izmit
More LessThe gulf of Izmit is located at the eastern Marmara Sea and has an east-west elongated rectangular shape with about 60 km length in east-west direction and 2-10 km width in north-south direction (Figure 1). The gulf is comprised of three basins, from west to east, western (Darica), central (Karamursel), and eastern (Izmit) basins. The central basin is connected to the other basins by two shallow sills located north of the Hersek peninsula and north of Golcuk at about 55 and 38 m water depths, respectively. The centrally located Karamursel basin constitutes the deepest part of the Gulf with a maximum depth of about 205 m.
-
-
-
Boru Hatları Tasarım Kriterleri ve Üç Boru Hattımızın Ekonomik Değerlendirilmesi
Authors U. Serpen and E.B. CebeciBu çalışmada boru hattı tasarım kriterlerine göre hazırlamış modeller ve metodoloji ile yapılması planlanan boru hattı projeleri ve hali hazırda işletmede bulunan boru hatları için tarife hesaplamaları yapılmış, bulunan neticeleri mevcut tarifelerle karşılaştırılmış ve sonuçları sunulmuştur.
-
-
-
Case Histories Illustrate escalating use of Monobore Expandable Liner Extensions incorporated into well designs to facilitate Drilling and Completing Trouble zones while eliminating NPT
Authors C. Stockmeyer and S. AtmacaThe Baker Hughes linEXX™ monobore expandable liner extension system places a liner string in the wellbore below an existing casing string and expands it, resulting in a liner with the same inside diameter (ID) as the previous casing string. When planned in your casing design, this system will isolate trouble drilling zones such as sloughing, unstable formations, and thief zones while maximizing hole size and without reducing the casing ID. The system can be applied in wells with anticipated trouble drilling zones such as depleted reservoirs or wells with narrow margins between pore pressure and fracture pressure, thereby eliminating the associated costs of managed drilling, chemical treatments and nonproductive time (NPT). Critical drilling problems of collapsed hole, lost circulation, substantial NPT, and costs associated with chemical treatments are effectively resolved or negated by using the monobore expandable extension system. Unlike other solid expandable systems on the market, the linEXX system provides an additional barrier without a loss of hole size, allowing the use of conventional bit and tubular sizes. Its top-down approach lets you place an expandable liner string in the wellbore while letting you maintain the same casing drift of the previous or existing intermediate casing string. The system is available in 9-⅝ in. or 9-⅞ in. sizes. When used as part of the base casing design, the linEXX liner not only optimizes hole size to the reservoir, but also eliminates costly NPT typically involved with the openhole section that would have required a conventional step-down liner.
-
-
-
Surface Deformation Analysis Over A Hydrocarbon Reservoir Using InSAR with ALOS-PALSAR Data
By S.C. SahinInterforemetric Synthetic Aperture Radar (InSAR) has been developed to estimate the temporal change on the surface of Earth by combining multiple SAR images acquired over the same area at different times. In the last two decades, in addition to conventional InSAR, numerous multiple acquisition InSAR techniques have been introduced, including persistent scatterer (PS) and small baseline subset (SBAS). In this project, we used the SBAS method to detect the surface deformation over a hydrocarbon reservoir in Adiyaman Providence, Turkey. The SBAS technique is performed on combinations of SAR images that are characterized by small orbital distances with large time intervals. By applying singular value decomposition (SVD), the temporal sampling rate is increased and those subsets are connected. We applied the SBAS method to five ALOS-PALSAR fine-beam dual (FBD) mode images, and removed the topographic phase by using a 3 arc-sec SRTM digital elevation model (DEM). Our analysis has revealed that due to the effective mitigation measures taken by the Turkish Petroleum Corporation, the maximum observed satellite line of sight (LOS) displacement velocity in the oil field is 5 mm/yr with a likely uncertainty of a similar magnitude in the period of 2007-2010. The high uncertainty estimate is due to the other spatially correlated signals of similar and larger magnitude seen in regions outside of the oil field.
-
-
-
(1) New pdc bit technology improved drilling performance in soft formation in boldesti area of romania and in challenging off-shore drilling environment on troll, norway. (2) New hybrid bit technology set record run in Turkey
Authors T. Schwefe and H. OueslatiNew PDC Bit Technology improved drilling performance in soft formation in Boldesti area of Romania and in challenging off-shore drilling environment on Troll, Norway.
-
-
-
Recovery of flare gas from technical, economic and environmental perspectives: El Gamil gas field case study, Egypt
Authors W.H.A. Moati, M.E. Fekry and S.I. ZayedFlaring is a process in which gaseous hydrocarbons are burned to prevent uncontrolled releases into the surrounding atmosphere and to relieve dangerous equipment overpressure conditions or any other operational upsets. The most recent data reported by the world bank’s global gas flaring reduction partnership (GGFR) indicate that 150×109 cubic meters (m3) [5.3×1012 cubic feet (ft3)] of natural gas are flared annually, and this quantity results in 400 million tons of carbon dioxide,CO2 emissions. This calls for encouraging the opportunities to eliminate continuous flaring of the associated and dissolved gases at production sites to improve the energy efficiency and contribute to the climate change mitigation and hence achieve the sustainable development in oil and gas industry. The paper introduces a field study at El-Gamil gas plant, a gas processing plant located at Portsaid city on the northern east coast of Egypt. The plant collects the gas and condensate production from offshore wells in the Mediterranean Sea to be processed at onshore in low temperature separation units ‘LTS’ and condensate treatment units to meet sales specs. In the 2nd quarter of 2004, a new project consists of 4 multi-stage compressors started to recover excess-off gas coming from the condensate treatment units and compresses it to the pressure of raw gas from wells to be processed prior to sale. This project is evaluated from technical, economical and environmental perspectives to provide a broad image for any waste gas recovery project. Meanwhile; improving the suitability in O & G sector and increasing available supplies.
-
-
-
Germik Field Garzan Formation 3D Facies Modeling
Authors C. Çetinkaya, E. Yılmaz, M.Ö. Türkmen and M.Z. AlperGermik Field, which started production in 1958 with the discovery of Germik-1 well, is still one of the oil producing fields within the boundaries of the city of Batman. However, due to considered to be in the class of mature oil field, the oil production of Germik has gradually decreased in recent years. This situation has brought about the implementation of the secondary production techniques in the field.
-
-
-
Saturation-Height Modeling of Bozova Oil Field
Authors M.Ö. Türkmen and S. EvinThe capillary-saturation function plays an important role in describing fluid distribution and modeling flow in reservoir simulation. In this study, saturation height functions have been developed as part of an integrated petrophysical analysis of an oil field. Bozova Field is an oil field located in the Southeast Turkey. From the discovery of the field in 1995 to date, the production is made from a Maastrichtien age bioclastic limestone facies called Reservoir Level with approximately 18 % porosity and 27-40 m thickness (Figure 1). In this relatively mature field, a simulation study is realized to predict the field’s response to a prospective water-flooding program. To prepare a representative data to be used in the simulation model, log derived water saturation calculations are revised by considering the produced water values and capillary pressure measurements coming from special core analyses. In this case study, model used to calculate water saturation from logs include the deterministic Archie Equation. This equation is appropriate knowing the reservoir consists of clean bioclastic limestone facies. However, the resistivity logs are unable to give a proper idea about water saturation distribution respect to depth because of the fact that, they have almost same range of readings along the reservoir section. Using Archie model with a fixed value for water resistivity (Rw) causes mismatch between simulation with real water production history. This problem has led us to reevaluate the logs with the observed salinity data from the wells. After applying this correction, saturation height models are developed from core capillary pressure (Pc) data to calculate water saturation vs. depth, which is independent of logs. First step of the procedure is to model capillary pressure measurements using different methods, namely, Brooks-Corey, Lambda, Thomeer and Leverett-J functions. After this stage, each of these models is used to estimate water saturation along all the wells. Eventually, the best fit between log derived saturations with the capillary derived saturations is achieved using the Leverett-J Function model (Figure 2). The results show that, the saturation height functions provided more accurate water saturation values in Bozova oil field and they have mostly overcome uncertainties associated with log interpretation by use of Archie model. Newly created water saturation logs are used in the water saturation distribution of the geological model to calculate oil-in-place volume (Figure 3). This distribution shows better agreement with the production data of the field and with the oil-in place calculation made in the simulation stage. Linking the core capillary pressure data with well log analyses has enhanced the water saturation estimations.
-
-
-
Fracture Analysis And Characterization of Şambayat Oil Field
Authors M.E. Gözel and M.Ö. TürkmenThe characteristics of the fracture network have an important role on the development of naturally fractured reservoirs because of their control on the storage capacity and flow dynamics in the reservoir. It is essential to understand the fracture networks in respect to orientation, intensity and spatial distribution for a successful development of a naturally fractured reservoir. Southeast Anatolia, as a tectonically active region, mostly has fractured carbonate oil reservoirs that need to be analyzed in terms of above characteristics.
-
-
-
Rezervuar Kayacı Islatımlılığının İnce Tabaka Kılcal Yükselim Yöntemi ile Tayin Edilmesi
Authors F.B. Hoşgör, H.Ö. Yıldız and A.A. SirkeciBu çalışmada, minerolojik olarak heterojen kompozisyona sahip gözenekli madde ile temas halinde olan iki karışmayan akışkanın katı yüzeyi ile oluşturacakları temas (kontak) açısının saptanabilirliği araştırılmıştır. Temas açıları saf mineral yüzeylerinde ölçüldüğü için, farklı içeriklere sahip kayaçların ıslatımlılığını ne kadar doğru temsil edeceği şüphe içermektedir. Rezervuar kayaç yüzeyinin, pürüzlülüğü, heterojenliği ve emilimi nedeni ile kontak açısı direk olarak ölçülemez. Kontak açısı direk olarak ölçülemediğinden, kayaçların ıstamlılığını karakterize edebilmek için kayacı oluşturan partikül yatağındaki kılcal yükselme ölçülebilir. Bu çalışmanın amacı, kayaçların ıslatımlılıklarının İnce Tabaka Kılcal Yükselme yöntemi kullanılarak tayin edilmesidir. Bu araştırmada, kontak açılarının dinamik hesaplanmasında kullanılan Washburn denklemi ve bu denklemin İnce Tabaka Kılcal Yükselme (Thin Layer Wicking) yöntemine olan uygulaması açıklanmıştır. Bu deneysel çalışmada, öğütülerek toz haline getirilmiş numune “powder” olarak çeşitli kumtaşı ve kireçtaşı kayaç örnekleri ile bu kayaçları oluşturan temel saf mineraller (kuvars ve kalsit) kullanılmıştır. Yükselme sıvısı olarak da saf su, ağırlıkça %2’lik NaCl çözeltisi, gazyağı ve mineral oil kullanılmış ve bunların numunenin katı yüzeyinde oluşturdukları temas açıları saptanmıştır. Buna göre, toz halindeki kuvarz mineralinin toz halindeki kalsit mineralinden daha fazla su ıslatımlı olduğu ispatlanmıştır. Ayrıca, Berea ve Bentheim kumtaşlarının temas açısı değerleri kuvarz mineralinin; karbonatlı kayaçların temas açısı değerleri kalsit mineralinin temas açılarına yakın bulunmuştur. Bu çalışma, petrol ve doğal gaz mühendisliği alanında İnce Tabaka Kılcal Yükselme yöntemi ile yapılan ilk çalışmadır ve ileride bu konuda yapılacak araştırmalara öncülük edebilir.
-
-
-
Compressional and Tensile Strengths of Miocene Sandstones of Eastern Mediterranean
More LessThis paper discusses experimental results of compressive and tensile (Flexural, Brazilian and Direct Pull) strength tests conducted on Miocene sandstone samples from Eastern Mediterranean. Compressive and tensile strengths of rocks are very crucial in petroleum industry since evaluation of those properties help to make a good hydraulic fracturing program and also required to control wellbore stability in both vertical and horizontal wells. In the Eastern Mediterranean offshore gas has been discovered in Miocene Sandstones by Israel and South Cyprus Greek Administration. Equivalents of these sandstones are cropping out at Karpaz Peninsula of the Northern Cyprus. Fresh unaltered rock samples from these outcrops have been collected and tested for their mechanical properties in the laboratory. Special emphasis in the study was given to lamination effects on rock strength and on fracture directions.
-
-
-
Vibro Verisinde Faz Dönüşümünün Ters Evrişim Uygulamalarına Etkisi
More LessVibro sismik çalışmalarında kaydedilen sismik iz, sweep sinyali ile sismik dalğacığın ve yerin yansıma katsayıların evrişimi olarak tanımlanır. Sweep sinyali ile vibro kayıdının korolasyonundan sonra sweep sinyali öz ilişkisine dönüşür, bu kauder dalgacığı olarak adlandırılır. Klauder dalgacığı sıfır fazlı olup simik dalgacık ise minimum fazlıdır, her ikisinin evrişimi sonunda ise karışık fazlı bir dalgacık oluşur. Bu durumda iğnecikleştirme ters evrişimi için minimum faz operatörü, klauder dalgacığının minimum faz eşleniğinden bulunur ve korolasyonu yapılmış vibro izine uygulanır. Bu çalışmanın amacı vibro verisinde minimum faz dönüşümünün ters evrişim üzerindeki etkisini araştırmak ve ortaya çıkarmaktır. Korolasyonu yapılmış vibro datasına minimum faz operatörü uygulanarak iğnecikleştirme ve ön kestrim ters evrişimi uygulanmıştır. Ayrıca minimum faz dönüşümünden önce de ters evrişim uygulanarak faz değişiminin ters evrişim üzerindeki etkisi araştırılmıştir. Faz düzeltmesinden önce ve sonra uygulanan ters evrişim sonuçları karşılaştırıldığında iğnecikleştirme ters evrişiminde faz düzeltmesinin daha etkin olduğu, ön kestirim ters evrişim sonucunun ise daha az etkin olduğu gözlemlenmiştir.
-
-
-
Kuzey Meksika Körfezi’ndeki Sığ Bir Fay Sisteminin Rezervuar Bölümlendirilmesi ve Geçirimsizlik Analizi
By B.T. ÜstünFaylar, rezervuardaki temel heterojenliklerden biridir. Hidrokarbonlar için ya bir kapan ya da akış yolu oluşturabilirler. ‘Fay Sızdırmazlık Analizi’ hem arama şirketleri hem de yapısal jeoloji araştırmacıları için fay karakterlerini daha iyi anlamada en önemli konulardan biridir. Fayların geçirimsizlik kapasitelerinin tahmininde farklı yöntemler geliştirilmiştir. Ancak, araştırmacılar tarafından fayların geçirimsizliği ile rezervuar bölümlendirilmesi konusuna yeteri kadar önem verilmemiştir. Fay geçirgenliği, faya komşu fasiyeslerin litolojisine olduğu kadar, fay zonunun kum/şeyl içeriğine de bağlıdır. Sızdırmazlığa etki eden pek çok süreç olsa da, sıvı göçünü etkileyen fay zonu bileşimi bunlar arasında en önemlisidir. Meksika Körfezi (ABD)’nde yer alan Main Pass 138 isimli sahanın log dataları, fay geometri ve sızdırmazlığının belirlenmesinde sismik ve kuyu verisi birlikte yorumlanarak bir yöntem oluşturulmuş ve bunlar kuyu basınç ve üretim verisi ile karşılaştırılmıştır. Bu çalışmada, Newfield Exploration Company (NEC)’ye ait Main Pass Block 138 (MP138) üretim sahasından, 3 boyutlu (3B) sismik, 21 kuyudan alınmış GR, SP ve rezistivite logları, bazı kuyuların basınç ve üretim verisi kullanılmıştır. Kuyu logları, Petra (Geoplus) programı kullanılarak yorumlanmış ve korele edilmiştir. Daha detaylı korelasyon yapabilmek ve kum/şeyl oranlarını saptamak için VSH (şeyl hacim) logları oluşturulmuştur. Bu loglar, saha genelinde litolojilerin belirlenmesine ve kil hacimlerinin hesaplanmasına katkı sağlamıştır. Loglar ve check-shot verisi ile birlikte 6 büyük normal fay ve seviyeler Seisworks-3D (Landmark) programı kullanılarak yorumlanmıştır. Bu seviyeler, en önemli üretken kum paketlerinin de dahil olduğu Senozoyik yaşlı 15 seviyedir. Fay sızdırmazlık analizi için TrapTester programında ‘Shale Gouge Ratio (SGR)’ algoritması kullanılmıştır. SGR hesaplaması, fay zonundaki şeylli malzemenin oranını tahmin etmeye yarayan bir algoritmadır. Fristad et al. (1997), Yielding et al. (1997) and Freeman et al. (1998) tarafından tanımlanmıştır. Algoritma, fay yüzeyindeki her bir noktadan kayan kayaç hacmindeki şeyl veya kil içeriğini hesaplamaktadır (Şekil 1; Yielding et al., 1997; Freeman et al., 1998). MP138 sahasındaki yorumlanan önemli fayların hepsi KD-GB doğrultulu tuz ile ilişkili bir genişleme tektoniğine bağlı bir sistemin ürünleridir. Tuz yorumlanmamış olmamasına rağmen literatürden bu fayların tuz tektoniğinden etkilendiği bilinmektedir. Fayların atımı 50-500 ft (15-152 m) arasında değişmektedir. 1’den 6’ya kadar numaralanan fayların çoğunun SGR yöntemi ile yapılan analize göre geçirimsiz olduğu ortaya konulmuştur. Fay 3’ün (Şekil 2) fay 1’e (Şekil 3) göre daha çok sızdırma kapasitesi vardır. Atımı diğerlerine göre fazla olan fay 1’in geçirimsizlik kapasitesi de diğerlerine göre fazladır. Fay 2, 4 ve 6 için kuyu verisi yeterli olmasa bile onların da geçirimsizlik özelliği olduğu ortaya çıkmıştır. Şeyl içeriği, SGR hesaplamalarını etkileyen en önemli faktördür. Fay zonunda şeyl oranı fazla olan bölgelerin sızdırmazlığı da fazladır. Bu çalışmada, sadece fay 1 ve 3 için basınç verisi analiz edilebilmiştir. Basit basınç kalibrasyonu yöntemine göre 16500A1, A4ST ve A6 kuyularının üretim verisi ile fay 1’in sızdırmazlık kapasitesi sonucu uyumlu, fay 3’ün uyumsuz çıkmıştır. Bu çalışmada fay geçirgenlik analizi yapılırken, şeyl içeriği ve kılcal basıncın etkileri yanında, fay atımlarının, kayaç özelliklerinin ve hidrokarbon kolonunun yüksekliğinin de önemi vurgulanmıştır. Basınç ve üretim verisi, geçirimsizlik tahminlerini doğrulamada yetersiz kalsa da, çalışmada mümkün olduğunca çok etmen test edilerek, belirsizlikleri ve riskleri azaltmak amaçlanmıştır. Elde edilen analiz sonuçlarının, MP138 sahasının geliştirilmesinde ve benzer fay sistemlerinin anlaşılmasında önemli etkileri olabilir.
-
-
-
The Impact of Porosity Uncertainty in Reservoir Modeling Using Multiple-Point Geostatistics
Authors M. Fadlelmula, S. Akin and H.Ş. DüzgünThis study provides a systematic way to investigate the propagation of porosity uncertainty through the estimate of original and recoverable oil in place (OOIP and ROIP) of an original reservoir model. To perform the intended investigation, a multiple-point geostatistics (MPG) modeling methodology is adopted. Then, a synthetic fluvial reservoir model (original reservoir) is generated utilizing a given dataset. Next, different realizations of the original data are generated through Monte Carlo Simulations (MCS) based on quantified uncertainty values in the porosity. Following that, the original reservoir is remodeled using the generated realizations. Finally, the OOIP and ROIP of the new reservoir models and their percentage errors with respect to those of the original reservoir are computed and analyzed. The results show that the estimates of the OOIP and ROIP move from overestimation to underestimation as the uncertainty increases from 0.01 to 0.15. This clearly shows that the uncertainty of porosity has a great impact on the model outputs. Thus, it should be given great care to facilitate more accurate reservoir modeling applications.
-
-
-
Türk Petrol Kanunu Tasarısı
By İ. BahtiyarYerli petrol kaynaklarımızın aranması ve üretilmesi, ekonomik olmasına rağmen ülkemiz için stratejik öneme sahiptir. Dünyanın her ülkesinde taşıdıkları potansiyele uygun olarak, bu kaynakların azami aranmasını teşvik edici, yatırımcı ile devlet arasında paylaşımı adil kılan yasal düzenlemeler tercih edilmektedir. Bazı ülkelerde ise, gelişen koşullara bağlı olarak yeni düzenlemeler yapılabilmektedir. Günümüzde ülkelerde üç ana anlaşma modeline sahip yasal mevzuatlar kullanılmaktadır.
-
-
-
Petrol Arama Üretim Faaliyetlerinin Petrol Kanunları ve Tasarıları Açısından İncelenmesi ve Sektörün Geleceğinin Değerlendirilmesi
More LessBilimsel objektiflik; gerçekliği (realiteyi), “olduğu gibi”, “sübjektif önyargıların etkisinde kalmadan” tespit etmektir. Toplumlara baktığımızda, toplumsal gerçekliğin (realitenin) kendisinde “tarafçılık” vardır. Bilimsel, objektif tespit toplumda bir tarafın işine gelir, öbür tarafın işine gelmez. Bildiri ile kanunun geçmiş değişim sürecini, ileriye dönük bir biçimde ortaya koymaya, gelecek için açıklamalar ve ileriye dönük irdelemeler için gözden geçirilmesi hedeflenmiştir. Kabul edilen tüm kanunlar, ülke petrol kaynaklarının süratle, devamlı ve verimli bir şekilde geliştirilip kıymetlendirilmesini esas amaç olarak almakla birlikte değişiklikler siyasi otoritelerin faaliyetlere bakış açısını da yansıtmaktadır.
-
-
-
Türkiye’de Üretilen Ham Petrol ve Doğal Gaz’ın “Piyasa Fiyatı için Hukuki ve Mali Düzenlemeler ve İrdelenmesi
More LessTürkiye’de yerli ham petrol (domestic crude oil) fiyatı için piyasa fiyatı (market price) tespi usulu 2003 yılında çıkarılan 5015 sayılı Petrol PiyasaıKanunu’nun (Petroleum Marketing Law) 10.maddesi ile değiştirilmiştir. Ancak piyasa fiyatı tespiti için getirilen usul ve kıstaslar dünya petrol sektörünün kabul ettiği prensiplerle uyuşmamamaktadır. Mevcut kanun ile tespit edilen yerli (domestic) iyi kaliteli ham petrolün fiyatını düşük tespit etmekte ve üreticiyi maddi olarak cezalandırmaktadır. Ayrıca Hazine deDevlet Hissesi (royalty) geliri bakımından zarar görmektedir.Bu sebeple yeni düzenlemelerle piyasa fiyatın(Market price)Türk Petrol Kanun tasarısı kapsamına alınması önem taşımaktadır.
-
-
-
Yerli Ham Petrol ve Doğal Gaza Uygulanan Mali Rejimin ve Türk Petrol Kanunu Tasarısı’nın Değerlendirilmesi
More Less2004 yılından itibaren artan ham petrol fiyatlarına paralel olarak bütün ülkeler mali rejimlerini yeniden düzenleyerek devlet ve şirket aldılarını adaletli bir düzeye getirmişlerdir. Türkiye’de üretilen yerli ham petrol için herhangi bir mali rejim düzenlemesi yapılmadığından Hazine her yıl büyük gelir kaybına uğramaktadır. Dünyada petrole uygulanan Mali rejimler incelenerek ülkemize uygun olan bir sistemin yeni Türk Petrol Kanunu tasarısında yer alması önemli bulunmaktadır.
-
-
-
Türkiye’nin İlk ve Tek Yeraltı Gaz Depolama Tesisinin Tasarımı ve İlk Altı Yıllık Operasyon Performansının Değerlendirilmesi
Authors S. Şahin, S. Abravcı and A. TirekGaz kaynakları yönünden ülkemizin zengin olduğu söylenemez. Yurtiçi üretim Türkiye’nin doğal gaz ihtiyacını karşılamaktan çok uzaktır. Türkiye’de tüketilen gazın tamamına yakını boru hatlarıyla Rusya Federasyonu, Azerbaycan ve İran’dan, LNG olarakta Cezayir ve Nijerya’dan ithal edilmektedir. Gaz tüketen ülkelerin çoğunda olduğu gibi, Türkiye’nin de gaz kullanımı günlük ve mevsimsel bazda değişim göstermektedir. Üretim ve tüketim noktaları arasındaki gaz boru hatları, tek başına, arz ve talep arası farkları dengeleyebilecek güce sahip değildir. Bu yüzden, ülkenin gaz taşıma ve depolama kapasitesinin geliştirilmesi için çalışmalar kesintisiz bir şekilde sürdürülmelidir. Söz konusu çalışmaların bir parçası olarak, Türkiye Petrolleri Anonim Ortaklığı (TPAO) Kuzey Marmara (deniz) ve Değirmenköy (kara) sahalarının yeraltı gaz deposuna dönüştürülmesini kararlaştırmıştır. Kuzey Marmara (K.Marmara) ve Değirmenköy sahalarının depolama amaçlı kullanım için seçilmelerinin temel nedeni ana gaz tüketim merkezi olan İstanbul’a ve ana gaz boru hattına yakınlık ve sahaların rezervuar karakteristiklerinin depolama için uygunluğudur. Ancak, tatil yöresinde ve yerleşim alanlarına yakın olması nedeniyle proje sahası çevre yönünden duyarlı bir bölgededir. Ses, atmosferik emisyonlar ve diğer kirleticiler konusunda kurallar katı bir şekilde uygulanmaktadır. 1.9 milyar m3 depolama kapasitesi ile Silivri (K.Marmara ve Değirmenköy sahaları) yeraltı gaz depolama (YGD) tesisleri 13 Nisan 2007 tarihinde devreye alınmıştır. Söz konusu tesisler, gelişmekte olan gaz sektörünün arz ve talep ilişkilerinin dengelenmesinde önemli işlevler yerine getirmektedirler. Bu makalede, Türkiye’nin ilk ve tek yeraltı gaz depolama tesisinin tasarımı ve yapımı hakkında bilgi verilmekte, ayrıca, altı yıllık çevrimi içeren veriler temelinde tesislerin işletme performansı değerlendirilmektedir.
-
-
-
Doğal Gaz Depolamanın Gaz Piyasasındaki Rolü
By R. ErenTürkiye’nin ilk yeraltı doğal gaz depolama tesisi olan TPAO Silivri Doğal Gaz Depolama Tesisi 2007 yılında devreye alınmış olup, 7. Depolama döneminde enjeksiyon ve geri üretim faaliyetlerine başarı ile devam etmektedir. 2012 yılına kadar sadece BOTAŞ’a hizmet veren TPAO Silivri Doğal Gaz depolama tesisi, EPDK tarafından çıkarılan “TPAO Silivri Doğal Gaz Depolama Tesis Temel Kullanım Usul ve Esasları”nın Resmi Gazete yayımlanmasının ardından 3. Tarafların kullanımına açılmıştır. Bu sunumda depolama tesisi türleri; yeraltı doğal gaz depolama tesisleri, LNG tesisleri ve boru hattında depolama (linepack) hakkında genel bilgi verilecektir. Ayrıca depolama tesislerinin kullanım amaçlarına göre; mevsimsel sıcaklık farklılıklarını gidermek için (seasonal storage), kısa süreli aşırı talepleri karşılamak için (peakshaving), stratejik amaçlar için (strategic storage), üretimi dengelemek için (production storage), sistemi dengelemek için (pipeline balancing) ticari amaçlar için (trade support) kullanılan depolama tesislerinin avantaj ve dezavantajları, yeraltı doğal gaz depolama tesislerinin Dünya ve Avrupa’daki depolama türlerine göre dağılımları ile ilgili genel bilgiler verilecektir. Avrupa gaz piyasasının liberalleşmeye duyduğu ihtiyaçlar, kronolojik olarak liberalleşme süreci ve liberal piyasanın etkileri ve Third Party Access (TPA) süreci ile ilgili bilgilendirmeler yapılacaktır. Ayrıca, TPA ile ilgili Avrupa’daki düzenlemeler ve ülkeler bazında mevcut düzenlemeler (Regulated TPA, Negotiated TPA ve Hybrid Systems) ve Türkiye’deki mevcut durum karşılaştırılacaktır. Depolama Sistem Operatörleri (Storage System Operators-SSO) için 2005 yılında yayımlanan, herhangi bir zorunluluğu olmayan ancak depolama tesislerinin kullanımına ilişkin olarak önemli düzenlemeler getiren “Guidelines for Good TPA Practice for Storage System Operators (GGPSSO)”- 23 Mart 2005 ile ilgili olarak bilgilendirme yapılacak olup, TPAO Silivri Doğal Gaz Depolama Tesisinin mevcut düzenlemeler çerçevesinde GGPSSO ile olan ilişkisi ele alınacaktır. Son olarak, depolama tarifeleri, tarife elementleri (Bundled, Unbundled, Hybrid v.b), cezalar, tarifelerin değişiminde etkili olan limitler (günlük geri üretim/ enjeksiyon kapasitesi, günlük minimum geri üretim/ enjeksiyon miktarları, geri üretim döneminde enjeksiyon veya enjeksiyon döneminde geri üretim yapabilme kabiliyeti, sadece belirli tarihlerde enjeksiyon yapma, enjeksiyondan geri üretime veya geri üretimden enjeksiyon geçiş süresi v.b.) ve TPAO Silivri Doğal Gaz Depolama Tesisi depolama tarifeleri ile ilgili bilgilendirme yapılacaktır.
-
-
-
Designing an underground gas storage field using the RUBIS software
Authors F. Daneshvar, Ö.İ. Türeyen and A. SatmanIn this study, the X gas field is modelled as a storage pool. It is a hypothetical dry gas field with field and fluid properties assumed to be similar with the northern Marmara gas field. The storage gas reservoir performance is modelled by using the Rubis software. Two scenarios are considered in this modelling study. These scenarios are used to determine the required number of wells for various cases considering the types of wells (vertical versus horizontral), the effects of skin factor, the horizontal length, and the wellhead flowing pressure constraints. The details of criteria and assumptions involved in scenarios are given in the paper. The results of this modelling study are presented in tables and figures.
-
-
-
Effect Of Compositional Change In Kuzey Marmara Reservoir On Storage Capacity
More LessTurkish Petroleum Company (TPAO) has served the first underground gas storage facility called as “Kuzey Marmara and Değirmenköy Fields Underground Gas Storage Facilities” to Turkey economy on 21.03.2007 where it was initially started to execute in 1996 by considering the need of gas storage facility of Turkey. The fields used in the scope of project are depleted gas reservoirs. Storage facilities consist of Kuzey Marmara and Değirmenköy Fields Gathering Points and a Shared Facility used for injecting gas to reservoirs and processing and serving the withdrawn gas to BOTAŞ Main Pipeline. Storage activity is mainly comprised of injection phase, injection of processed gas taken from main distribution line via shared facility, and withdrawal phase, production of mixture of injected processed gas with cushion gas. A storage period consists of withdrawal process following up injection process and original and injected gas have different compositions. It is observed that such compositional difference results composition change in withdrawn gas. In this study, percentage rate of change of withdrawn gas composition to original gas is determined by selecting Kuzey Marmara Reservoir gas composition as original composition before starting storage activity. Production amount has been determined at %5, %10 and %12 gas composition to original gas composition for each period. These production amounts are used for comparison for each storage period to get an idea about compositional change of reservoir. It has been observed from the tests performed when there is no operation (injection or withdrawal) that the pressure of each well changes simultaneously. Thus, it has been concluded that the measured pressure of any well represents the whole reservoir pressure characteristic. Hence, well no 8 in Kuzey Marmara has been selected as the pilot well and pressure of this well has been assumed to represent the reservoir pressure. The effect of changes in gas composition on the storage capacity has been examined by correlating the amount of gas withdrawn from the reservoir and the pressure attained on the injection period for each storage year (period). It has been anticipated to achieve significant results by making use of obtained data in the oncoming years in that study.
-
-
-
Yüksek Genlikli-Düşük Frekanslı Gürültülerin Wiener Kestirim Yöntemi ile Süzgeçlenmesi
Authors H. Karslı and D. DondururYüksek genlikli ve düşük frekanslı gürültü türlerinden ground-roll gürültüsü kara ve deniz dalgası gürültüsü ise deniz verilerinin işlenmesinde problemler çıkarmaktadır ve bu gürültülerin verilerin spektral içeriğine zarar vermeden veriden atılmaları dikkat edilmesi gereken önemli bir aşamadır. Bu çalışmada her iki gürültünün süzgeçlenmesinde Wiener kestirim süzgecinin nasıl kullanılacağı gösterilmiştir. Uygulamalarda giriş verisinin düşük frekans enerjilerini kaybetmeden süzülmesi üzerine odaklanmıştır. Yöntem gerçek verilere uygulanmış ve hem zaman hem de spektral çıktılar üzerinde karşılaştırılmıştır. Wiener kestirim süzgeçlemesinin yığma kesitlerine katkısı bir deniz verisi üzerinde gösterilmiştir. Yaygın sismik veri işlem yazılımlarının rutin süreçleri olan frekans seçici süzgeçlemelere (f-k, bant geçişli) ile karşılaştırıldığında, ground-roll ve deniz dalgasının atılmasında yöntemin giriş verisinin düşük frekans enerjisini yüksek oranda koruduğu gözlenmiştir. Anahtar Kelimeler: Ground roll, Deniz dalgası gürültüsü, Wiener kestirim süzgeci.
-
-
-
Oligosen-Miyosen Yaşlı Jipslerin Yeraltı Doğalgaz Depolama Amaçlı Kullanılabilirliği
Authors A.T. Arslan, C. Kıncal, B. Kahraman, Ç. Pamukçu, O. Pamukçu, E. Gök, O.D. Polat, M.Y. Koca, H. Konietzky, H. Temiz and H. KöseDünyada doğal gazın enerji kaynağı olarak kullanımı günden güne artmaktadır. Bu kullanımdaki artışa paralel olarak, doğal gaza olan talebinin kesintisiz olarak karşılanabilmesi için doğalgaz depolama konusunun önemi de artmaktadır. Ülkemizde de artan nüfus ve endüstrileşmeye paralel olarak doğal gaza olan ihtiyaç günden güne artmaktadır. Türkiye’de yurt içi doğalgaz üretiminin tüketimi karşılama oranı % 3 seviyelerindedir. Bu oran ve doğalgaza olan talebin önümüzdeki yıllarda artacağı gerçeği göz önüne alındığında, depolama ihtiyacı gelecek yıllarda çok daha fazla önem kazanacaktır. Günümüzde, yerüstünde ve yeraltında doğalgaz depolama tesisleri oluşturulmaktadır. Doğalgazın yerüstünde çelik tanklarda depolanması yerine, yeraltında depolanmasının çok daha güvenli, verimli ve ekonomik olduğu düşünülmektedir. Doğalgaz depolama tesisleri, tedarikte bir kesinti olması durumunda ülkenin acil ihtiyaçlarının karşılanması bakımından önemlidir. Yeraltı doğalgaz depolama tesisleri oluşturmak için çeşitli olanaklar mevcuttur. Bunlar; derin tuz çözelti açıklıkları, sığ derinlikte masif kaya kültesi içerisinde galeri şeklinde oluşturulan açıklıklar, yeraltı suyu akiferlerindeki gözenek boşlukları, üretimin sona erdiği petrol ve gaz sahaları ile uygun özelliğe sahip terk edilmiş maden ocaklarıdır. Türkiye’deki doğalgaz ve petrol boru hatlarının konumu incelendiğinde, Sivas ilinin bir kavşak konumunda olduğu görülür. Sivas ilinin bu konumuna ilave olarak, Hafik-Zara arasında kalan bölgede geniş jips yataklarının bulunması, doğal gaz boru hattına yakın olması ve arazi kullanım durumunun (tarım, orman v.b.) uygun olması gibi faktörler göz önüne alındığında, yeraltı doğalgaz depolama yeri olarak Sivas ili çok uygun bir konumda yer almaktadır. Bu nedenlerden dolayı jipsler ekonomiye kazandırılabilir ve doğal gaz depolama ortamı olarak kullanılabilir. Oligosen-Miyosen yaşlı jipslerin dayanım ve deformasyon özellikleri kısa ve uzun süreli olmak üzere incelenmelidir. Kısa süreli mekanik özellikler tek ve üç eksenli dayanım özellikleri ile deformasyon özellikleri başlıkları altında, uzun süreli mekanik ve deformasyon özellikleri ise değişik gerilme basamaklarında yüklemeler yapılarak deformasyona bağlı eksenel ve çapsal krip oranı ile ilgili parametreler belirlenerek yapılmalıdır. Bu sayede elde edilebilecek veriler ışığında jipslerde açılması düşünülen yeraltı doğal gaz depolama açıklıkları nümerik analiz programları kullanılarak modellenebilir elastik, elastoplastik, dinamik, sünme (krip) çözümlemelerinden elde edilecek sonuçlar toplu olarak değerlendirilebilir, yapılacak çözümlemeler sonucunda zamana bağlı viskoz davranış gözlenebilir, sünme modelleri ile doğalgaz depolama amaçlı duraylılık ve işletme güvenliği değerlendirilebilir.
-
-
-
Estimating the Location of Multiple Scatterers by Seismic İnterferometry of Scattered Surface Waves
Authors Z.E. Erdem, U. Harmankaya and A. KaslilarIn this study we use a recently proposed method to estimate the locations of multiple scatterers embedded in a halfspace. The method is based on active source seismic interferometry. Only one source at the surface is sufficient for the application of the method. Here, two scatterers separated sufficiently from each other and located at different depths and horizontal distances are considered. A synthetic shot record is obtained by modeling elastodynamic wave propagation and scattering. The scattered Rayleigh waves caused by the scatterers are used for location purposes. The scattered wavefields are extracted from the total wavefield by f-k (frequency-wavenumber) filtering. Different locations for virtual sources are chosen to obtain the interferometric images for these locations. The interferometric travel times of the scattered surface waves are used in inversion and the locations of the scatterers are estimated. Provided that the scatterers are sufficiently separated and the scattered wavefield is successfully extracted from the total wavefield, it is possible to estimate the location of the multiple scatterers.
-
-
-
DEÜ-DBTE-Seislab Çalışma Alanları’nda Sonar ve Deniz Sismiği Araştırmaları
By M. ŞenözTürkiye, Anadolu levhası ile komşu levhaları (Avrasya Levhası,Arap Levhası,Afrika Levhası) arasındaki levha sınırlarının birbirleri ile olan tektonik etkileşimlerinin şiddetli etkisi altındadır. Anadolu levhasının çevresindeki bu levha sınırları kuzeyde Kuzey Anadolu Fayı, doğuda Doğu Anadolu Fayı, güneyde Kıbrıs- Ege Yayı olarak bilinir ve Anadolu Levhası ile Ege Levhası arasındaki levha sınırı Kıbrıs-Ege Yayı’nın batı tarafında konumludur. Türkiye’nin bu büyük fay sistemleri çevresindeki denizlerimiz ( Ege Denizi, Doğu Akdeniz, Karadeniz, Marmara Denizi ) levha kinematikleri, sismisite, depremler, mikro-depremler, deprem hasarları, petrol, doğal gaz, kıyı yapıları, yüzey deformasyonları ve daha bir çok bakımdan dünyanın en kritik denizleridir. DEÜ DBTE uzun yıllardan beri sahip olduğu alt yapı ve araştırma gemisi K.Piri Reis ile bu denizlerimizin kıta sahanlıklarındaki araştırmalarını sürdürmektedir. Özellikle, sonar ve deniz sismiği teknolojilerini kullanarak toplanan, veri işlemlenen ve yorumlanan sismik veriler çok çeşitli deniz jeolojiksel ve jeofiziksel problemlerin çözümüne (Mühendislik Sismiği, Sediment Stratiğrafisi, Kıyı Yapıları, Batimetrik Haritalama, Deprem Hasarları, Petrol, Doğal Gaz, Gaz Hidrat, Soğuk Su Kaynakları vd…) katkı sağlamaktadır. 17 Ağustos 1999 tarihindeki Gölcük Depremi’nin ardından Marmara Denizi çok önemli bir alan haline gelmiş ve bu alanda deniz jeolojisi ve jeofiziği araştırmaları önceki zamanlardan farklı olarak aşırı yoğunluk kazanmıştır. DEÜ-DBTE Marmara Denizi’ndeki olağan araştırmalarını özellikle 2005 yılından beri SeisLab veri işlem laboratuarı ile güçlü bir şekilde sürdürmektedir. DEÜ-DBTE’nin araştırma gemisi R/V K.Piri Reis bu günde ulusal ve uluslar arası incelemelerde çok disiplinli bir kıta sahanlığı araştırma gemisi olarak, deprem hasarları, petrol, doğal gaz ve gaz hidrat ile ilgili konularda çok disiplinli ve uzun süreli projelere aktif destek sağlamaktadır.
-
-
-
Marmara Denizi Güney Şelfinde Toplanan 2B Çok Kanallı Sismik Yansıma Verilerinin Matlab ile Kalite Kontrolü, Veri İşlemi ve Yorumu
More LessKalite kontrol (QC), verinin toplanmasından yorumlama aşamasına gelinceye kadar olan dönemde veri kalitesini değerlendirmeye yönelik yapılan işlemlerin genel adıdır. Hedef; en iyi veri setini elde ederek, yorumlama aşamasında en ideal sonuca ulaşmaktır. MATLAB ile geliştirilen yazılım grupları (QC Programı) yardımıyla; sismik veri erişimi için sistem bileşenleri ile iletişimi sağlayan veri depolama birimlerinin kontrolü yanı sıra sismik veri ile eş zamanlı olarak toplanan konum verilerinin kontrolü de yapılmaktadır. Veri toplama süresince, sismik ve konum bilgilerinin görsel denetimini ve kontrolünü içerir. Çalışma süresince Marmara Denizi’ nin güney şelfinden alınan yüksek ayrımlı çok kanallı sismik yansıma verileri örnek veri seti olarak seçilmiştir. Bu veriler Dokuz Eylül Üniversitesi’ne ait R/V K.Piri Reis ile 2010 yılında Marmara Deniz’i güney şelfinde toplanmıştır. Bu alanda alınan verilere QC Programı ile kalite kontrol işlem adımları uygulanarak, laboratuvar ortamındaki veri işlem yazılımı ile karşılaştırılması yapılmıştır. Veri kalite kontrolleri ve ön veri işlem adımlarının hemen ardından ana veri işlem sürecinin başlatılması ve son olarak veri işlemi tamamlanmış verilerin yorumu olarak seyretmektedir.
-
-
-
Mikron Çapında ve Düşük Spesifik Graviteli Katı Malzemelerle Karıştırılmış Düşük Ağırlıklı Çamurların Reolojik Özellikleri
Authors B. Kutlu and E. ÖzbayoğluSürekli gelişmekte olan teknolojinin etkisi sonucunda ortaya çıkan yeni teknikler ve araçlar vasıtası ile petrol ve doğalgaz sektöründe devamlı olarak yeni keşifler yapılmakta, daha önce ulaşılması mümkün olmayan veya ekonomik olmayan kaynaklara ulaşılmaktadır. Düşük basınçlı rezervlerin bulunduğu çıplak kuyularda yönlü ve yatay sondaj ve kuyu tamamlama çalışmaları yaygınlaşmaktadır. Olgun petrol sahalarının yeniden canlandırılması ve düşük basınçlı rezervlerin değerlendirilmesi ihtiyacı düşük ağırlıklı sondaj sıvılarına olan gereksinimi meydana getirmektedir. Düşük basınçlı ve düşük geçirgenlikli rezervlerin bulunduğu seviyelerin sondajı esnasında, gerekli olan sondaj sıvısı ağırlığı aralığının üzerindeki ağırlık değerleri ile sondaja devam etmek kısmi veya tam çamur kaçaklarına sebebiyet verebilir.
-
-
-
Sondaj Dizisinin Çeşitli Burkulma Konumları ve Dönme Hızları için Halkasal Basınç Kayıpları
Authors Ö. Erge and M.E. ÖzbayoğluSondaj sıvısının eşdeğer dolaşım yoğunluğunu (equivalent circulating density), gözenek ve çatlatma basınç penceresi arasında tutmak zor, bir o kadar da mühim bir konudur. Özellikle deniz sondajlarında bu aralık dar olduğundan konu daha da önem kazanmaktadır. Bunun için, halkasal (annular) basınç kayıplarının isabetli bir şekilde hesaplanması gerekmektedir. Bu gereklilik, özellikle çoklu yanal (multilateral), ileri uzanımlı (extended reach) ve dar (slim hole) sondaj uygulamalarında öne çıkmaktadır. Gerçeğe daha yakın sonuçlar sağlandığı takdirde, daha başarılı bir kuyu kontrolü, uygun kullanımlı matkap hidroliği, uygun sondaj sıvısı programı ve pompa seçimi elde edilebilir. Saha ve deneysel uygulamalar, sondaj dizisinin dönmesinin ve dönüş hızının, halkasal basınç kayıplarını ciddi bir şekilde etkilediğini göstermiştir. Günümüzde kullanılan sondaj sıvıları, Newtonian olmayan özellikler göstermekte ve çoğu da Yield Power Law (YPL) modeli ile sınıflandırılabilmektedir. Bu çalışmanın odağı, yatay bir kuyu düzeneğindeki sondaj dizisi sıkıştırılırken, dönme hızının YPL sondaj sıvıları üzerindeki etkileri üzerinedir. Yapılan deneyler, sondaj dizisinin çeşitli burkulma (buckling) konumlarını ve burkulmuş veya burkulmamış haldeki türlü dönme hızlarını içermektedir. Sinusoidal, sarmal (helical) ve bu ikisi arasındaki geçiş halinin basınç kayıpları üzerindeki etkisi araştırılmıştır. Sunulan bu çalışma ile daha kesin bir kuyu dibi basınç kontrolü sağlanabilir ve sondaj uygulamalarındaki halkasal basınç kayıpları daha iyi anlaşılabilir. Bu da, daha güvenli ve optimize olmuş sondaj uygulamalarına dönüştürülebilir.
-
-
-
Incised Valley-Fills and Their Genetically Associated Lowstand Deltaic Sequences in the Late Permian Unayzah Reservoir of Saudi Arabia
By M. ŞenalpThe incised valley-fills and their genetically associated lowstand deltaic sequences were first reported by the author in the subsurface of the Upper Member of the later Late Permian Ash-Shiqqah Formation of Saudi Arabia. These very coarse- to fine-grained sandstones with excellent reservoir qualities form the uppermost part of the stratigraphically and genetically heterogeneous Permo-Carboniferous Unayzah Reservoir, and produce significant amount of sweet gas and light oil. Immense amount of data obtained from the measured sections at outcrops and from the exploration and production wells and large amount of cores with the help of palynologic studies provided valuable information on the stratigraphy, sedimentology and reservoir quality of these successions (Senalp and King, 1995; Senalp and Al-Duaiji, 1995; 2001; Senalp 2006). Their formation occurred during the opening phase of the Neo-Tethys Ocean. Stratigraphically, the Ash-Shiqqah Formation extends between the Unayzah Formation at the base and the Base Khuff D Carbonates at the top, representing the MFS P20 (260.4 Ma). It is separated from the underlying continental red bed Unayzah Formation by a thick caliche-formed crust of Pre-Ash-Shiqqah Unconformity surface. The Ash-Shiqqah Formation correlates with the Kaş Formation, and the Khuff Formation correlates with the Gomanibrik Formation of southeast Turkey.
-
-
-
Triyas Yaşlı Bakük Formasyonu’nun (Cudi Grubu, Güneydoğu Anadolu Bölgesi) Organik Jeokimyasal Özelliği ve Hidrokarbon Türüm Potansiyeli
By N.Y. ErikGüneydoğu Anadolu Bölgesinde Paleozoik Mesozoyik yaş aralığındaki kaya birimleri bulunmaktadır. Orta Triyas-Alt Jura yaşlı birimlerden özellikle Cudi Grubu içindeki Bakük Formasyonunun kaynak kaya potansiyeli araştırılmıştır. Örnekler, Bakük, Girmeli, Çamurlu, Telhasan, Dinçer, Kozluca ve Yolaçan Formasyonlarından oluşan Cudi Grubunu kesen 6 kuyudan sağlanmıştır. Bakük Formasyonunun kaynak kaya potansiyeli organik jeokimyasal ve organik petrografik yöntemler ile değerlendirilmiştir. Elde edilen sonuçlar Bakük Formasyonunun sıvı hidrokarbon türüm potansiyelinin olmadığı ancak gaz türetebileceğini göstermiştir.
-
-
-
Çardak-Dazkırı Havzası’ nın (Denizli-Batı Türkiye) organik maddece zengin kayaçlarının iz element içeriklerini kullanarak depolanma ortamının belirlenmesi
By D.B. KoralayBu çalışmanın amacı, Denizli civarındaki (Türkiye batısı) Oligosen yaşlı organik maddece zengin kayaçların iz element zenginleşmelerini ve mineralojik bileşimini belirlemektir. İncelenen örnekler Hayrettin Formasyonu’ nun bir kısmını oluşturur. Bu formasyon genellikle kömür ardalanmalı lagünel çamurtaşıkumtaşı, resif, konglomera arakatkılı kumtaşı ve biyoklastik kireçtaşından oluşmaktadır. Hayrettin Formasyonu’ nun farklı lokasyonlarından toplam 51 yüzey örneği toplanmıştır. Örneklerin toplam organik karbon (TOC, %) miktarları % 0.21 ve % 39.61 arasındadır. İz element çalışmaları sonucunda incelenen örneklerin kömürler için dünya ortalamasına gore Na, Mg, K, Ti, Cr, Rb, Cs, Ta, Hg ve U elementlerince zenginleştiği gözlenmiştir. Bu zenginleşmeler, organik maddece zengin sedimanların yakın alanlarında mineralizasyonların olabileceğini ifade eder. Diğer taraftan bazı iz elementler iyi bir çökelme ortamı işaretçisi olarak göz önünde bulundurulur. Çalışılan örneklerin Fe (% 3.94), Tl (1.33 ppm) ve Hg (1.31 ppm) konsantrasyonları weathering’ e uğramış karasal bir kaynağa ve kaynağın nehirler tarafından bataklık ortamına taşınmasına işaret eder. İncelenen örneklerin U/Th oranının ortalama 1.48 olmasından dolayı çökelme ortamının redoks koşulları suboksik-anoksik ortama işaret eder. Ayrıca (CaO + MgO + Fe2O3) / (SiO2) + Al2O3) oranının 0.22’ den küçük olması (0.20) zayıf indirgeyici çökelme ortamı koşullarına işaret etmektedir.
-
-
-
Thin Bed Contourite Seismic Imaging by Wavelet Transform
By S. SunjayWavelet (Mathematical Microscope) analysis of seismic data is made fashionable for thin bed precise subsurface imaging and interpretation. 3D seismic data interpretation for subsurface imaging of thin bed contourite systems is integral part of research work. Seismic expression of bottom current deposits from that of other related deepwater sediments (turbidites, hemipelagites, debrites, etc.), and to maximising the information that can be derived from seismic data. A wide variety of seismic facies are common in contourites, most of which are equally present in turbidite systems. Seismic facies associations that may be typical of contourites are still to be defined. Seismic characteristics also depend very closely on the methods of seismic acquisition and processing. Sediment waves and channels are very common both in contourite and turbidite systems, and not specifically diagnostic of either system. Slope deformation, sediment creep, and large-scale water-escape may cause a hummocky seismic facies that can be misinterpreted as sediment waves. The identification of hydrocarbon reservoirs from seismic data is a key issue in the oil industry. Texture Segmentation of a 3D Seismic Section with Wavelet Transform is employed for pattern recognition. Because of the segmentation, zones of different internal stratification are identified in the seismic section. This recognition is based on the comparison of the 3-D seismic data with the reference patterns extracted from the representative areas, characterized by different textures. In splicing 3-D seismic data, consistent processing is one of the key technologies because it has a great effect on imaging quality.Seismic geomorphology goal is to look for and recognize geologically or geomorphologically meaningful patterns in plan view as well as in section view. Seismic geomorphology, the extraction of geomorphic insights using predominantly 3D seismic data, is a rapidly evolving discipline that facilitates the study of the subsurface using plan view images. Methods evolved for generating horizontal and flatted slices, arbitrary traverses,wavelet attribute extractions and mapping, and rapid analysis of large complex data volumes.A geological feature must have an expression that is scientifically reasonable in multiple dimensions. Analyses of section view integrated with plan view images represents the integration of seismic stratigraphy with seismic geomorphology. Pattern recognition, involving the interpreter being able to recognize geologically significant features in plan view on 3D.the seismic data, is critical to the seismic geomorphological approach. In conjunction, it is also essential to cross reference plan view with section view images, thus integrating the geomorphology with the stratigraphy.
-
-
-
Çınarcık Havzası’nın Aktif Tektoniği ve Kuzey Anadolu Fayı’nın Marmara Denizi İçerisinde Çok Kanallı Sismik Yansıma ve Batimeri Verileri ile İncelenmesi
Authors O. Atgın, G. Çifçi, C. Sorlien, L. Seeber, M. Steckler, D. Sillington, H. Kurt, D. Dondurur, S. Okay, S. Gürçay, H. Sarıtaş and H.M. KüçükMarmara Denizi, aktif tektonik yapısı ve Kuzey Anadolu Fay Zonu’nun (KAFZ) yaratmış olduğu aktif depremsellik nedeniyle birçok araştırmacı tarafından odak konusu haline gelmiştir. KAFZ, Marmara Denizi içerisinde karmaşık bir tektonik yapıya sahiptir. Çalışma kapsamında İstanbul’a yakınlığı ile bilinen aktif bakımdan önemli olan Çınarcık Havza’sı incelenmiştir. Bu çalışmada 2008 yılında gerçekleştirilen TAMAM (Turkish American Multichannel Project) ve 2010 yılında gerçekleştirilen TAMAM-2 (PirMarmara) seferlerinde R/V K. Piri Reis gemisi tarafından toplanan çok kanallı sismik yansıma verileri ve Fransız deniz araştırma enstitüsü olan Ifremer kurumunun hazırladığı yüksek ayrımlı batimetri haritası kullanılmıştır. Proje kapsamında yaklaşık 3000 km yüksek çözünürlüklü çok kanallı sismik yansıma verisi toplanmıştır. Çalışmanın sonunda havzanın aktif fay haritası ayrıntılı bir şekilde ortaya konmuştur ve birçok çalışmada yer alan havzanın güney yamacından geçen büyük ölçekli bir fayın varlığına rastlanmamıştır. Havza çökellerinin stratigrafik yorumlamaları yapılmıştır. Havzada oluşan faylanmaların en yoğun olduğu bölgede kuzeygüney yönlü yıllık kümülatif açılma hesaplanmıştır. Tabakaların küresel deniz seviyesi değişimleri ve tabakaların eğimlenmeleri karşılaştırılarak yaşlar hesaplanmaya çalışılmıştır.
-
-
-
Concretions in Akçakoca Sandstone Member of Kusuri Formation (Lower-Middle Eocene), Western Black Sea
Authors A. Aktosun and B. VarolAkçakoca Sandstone member of Kusuri Formation is a channel fill sediments which were deposited in submarine fan system by turbidite mechanism during Early and Middle Eocene in the Western Black Sea, Turkey. They consist of channel axis (massive sandstone), channel margin, levee and their complex sequences. Submarine fans are important in the petroleum industry for their reservoir and source rock potential. In the Akçakoca region, natural gas has been produced from Akçakoca sandstones since 2007. In this region, the massive sandstones with various dimentions of concretions were deposited in the submarine fan system. These concretions have spherical, ellipsoidal and flattened ellipsoidal in shape and have variable diameters ranging between 0.1-2 m. Petrographically, they are classified as feldspathic litarenite (generally) and lithicarkose. The sandstone concretions generally are represented by clean sands (sand/clay ratios>=7:1; 9:1), and show poorly or moderately sorting. Whereas encompassed sandstones (host rock) are texturally (sand/clay ratios>=7:3; 9:5 ) and compositionally immature as indicated by significant feldspar, clay, volcanic, sedimentary and metamorphic rock fragments due to close provenance and rapid transport by short rivers and tectonically controlled basin margin. The massive sandstones are generally structureless, only having amalgamation surfaces but underlying unit is rich in bioturbations and dewatering products such as dish and ball-pillow and flame structures that indicate middle and upper fan deposition respectively. The environmental features imply that the concretions in the massive sandstones had resulted from dewatering process/soft sedimentary deformation that caused by remove of the clay matrix as suspension and subsequently precipitation of calcite cement or they were independently formed after rock formation in the late diagenetic period, resulted from ground water lenses involved precipitation of calcite cement, that occupied the intergranular and interparticular open spaces, leading to significantly reduced porosity and permeability of the massive sandstones. Based on the XRD analysis, calcite ratio is between 14% and 38% in the concretions. Porosity and permeability values of the host sandstones are generally high (5.6- 30.9% porosity, 0.02-320.67 md permeability). In conclusion; host sandstones with the high porosity and permeability values can be good reservoirs, but concretions within the host rock have not any reservoir features because of the low porosity and permeability values (3.2-7.8 % porosity, 0.02-0.09 md permeability). The concretions, embedded within the host rock, do not constitute the reservoir barrier and may have not a negative impact on the Akçakoca sandstones.
-
-
-
Doğu Karadeniz’ in Aktif Tektonik Yapısının Çok Kanallı Sismik Yansıma Verileri ile İncelenmesi
Authors S. Duymaz, G. Çifçi, S. Okay, D. Dondurur, D.C. Kim, H.M. Küçük, O. Atgın and S.H. BaeDünyanın en büyük iç denizlerinden biri olan Karadeniz, oldukça karmaşık bir jeolojiye sahiptir. Bölge çok sayıda çamur volkanı, kanal yapıları, kanyonlar, aktif faylar ve gaz hidratlar gibi birçok oluşum içermektedir. Bu sebeple Karadeniz birçok araştırmacı tarafından odak noktası haline getirilmiştir. Çalışma kapsamında Doğu Karadeniz bölgesinde yüksek çözünürlüklü çok kanallı sismik yansıma verileri toplanmıştır. Bu veriler ışığında bölgedeki aktif ve gömülü fayların belirlenmesi, fayların karakteristik özelliklerinin araştırılması ve yamaç aşağı kütle hareketlerinin incelenmesi bu çalışmanın amacını oluşturmaktadır. Bu kapsamda 2010 yılında Rize ve Trabzon açıklarında yaklaşık 740 km yüksek ayrımlı çok kanallı sismik yansıma verisi toplanmıştır. Toplanan sismik hatlar sismik veri işlem programları ile değerlendirilerek yorumlanabilir hale getirilmiştir. Bu bağlamda çalışma alanında literatürde olmayan ancak Türkiye Petrolleri Anonim Ortaklığının (TPAO) haritalarında yer alan Rize ve Trabzon fayları ile Pontid bindirme kuşağının izleri bulunmuştur.
-
-
-
Exploration of the Gas Field in Western High Related to Thrace Basin Using Seismic Method
Authors H. Sarıtaş, G. Çifçi, Y. Thomas, B. Marsset, A. Rochat, C. Grall, P. Henry, G. Westbrook, C. Sorlien and S. KerIn the Marmara Sea the North Anatolian Fault consists of a main strand and a few subsidiary branches. The main strand is made up of the Ganos (15 km long), Central Marmara (105 km) and North Boundary (45 km) fault segments (Okay et al., 2000). Western Part of the Central Marmara Fault crosses on The Western High which is located between Tekirdag and Central Marmara Basins. The Western High and Cinarcik Basin is one of the major regions of geological interest which is the area close to the NAF where evidence of gas hydrates and fluid escapes have been observed during previous scientific cruises. To understand the kinematics of the NAF and origin of the gas, collecting data was focused on these areas by the latter cruises. It started with TAMAM (Turkish-American Marmara Multichannel) cruise in July 2008 by R/V Koca Piri Reis which belongs to Dokuz Eylul University, and after that it continued with MARMESONET (Marmara Demonstration Mission Program supported by European Seafloor Observatory Network) in December 2009 by R/V Le Suroit opreated by IFREMER. This cruise consists of two legs; leg-1 is about collecting multibeam and AUV data, Leg-2 is about collecting High Resolution 3D Seismic data. The last cruise was carried out in June 2010 by R/V Koca Piri Reis, its aim was collecting 2D High Resolution Seismic Data. These studies were funded by EU ESONET MARMARA-DM Project. These 2D high resolution seismic data was processed by Hakan Saritas. 3D HR data which was processed by Bruno Marsset, Yannick Thomas and Alexis Rochat. 3D seismic data provide detailed information about fault distribution and subsurface structures. Computer-based interpretation and display of 3D seismic data allow for more thorough analysis than 2D seismic data. The objectives of this survey are to find locations of gas strata and gas hydrate formation in the western high related to Thrace Basin. Previos studies show us the gas components of Thrace Basin where have been found many industrial gas field and Western High in sea of Marmara are fairly the same. The other objectives of this survey are studying on geological structure of this area, understand kinematics related to dextral strike slip North Anatolian fault, focus on the mud volcano where close to NAF and observation gas fluid through to seabed, oil seepage and find its location. In conclusion, there were some cruises related to collecting various marine geology and geophysics data in the Western High. The investigations have been focused on gas hydrate, gas escape, location of the gas strata and tectonics related to Thrace Basin.
-
-
-
Biyodedektifler; Çevre Kirliliği Ve Petrol Sızıntılarının İncelenmesinde Biomarkerlerin Kullanımı Biodetective
Authors S.G. Turgut and N.Y. ErikBiomarkerler petroldeki en önemli hidrokarbon gruplarından biridir. Bunlar petrol içinde diğer geniş aralıktaki bileşenlere göre düşük miktarlarda (ppm) bulunmalarına karşın gaz kromatografikütle spektrometre (GC/MS) analizi ile kolayca belirlenebilmektedir. Petrolde alkanlar ve aromatikler gibi bileşenlere göre biomarkerler bozunmaya karşı daha dayanıklıdır. Ayrıca, biomarkerler farklı jeolojik şartlar ve yaşlarda farklı parmak izleri oluştururlar. Bu nedenle de bu moleküllerin kimyasal analizleri özellikle hidrokarbonlardan kaynaklanan çevre kirliliklerinin belirlenmesi, sızıntı petrolün kaynağının tespiti ve petrollerin ayrımlanma ve korelasyonu ile farklı koşullar altındaki bozunma etkilerinin belirlenmesi açısından büyük önem taşımaktadır.
-
-
-
Üretim Boruları ve Pompa Rodlarındaki Kusurların Tesbiti,Değerlendirilmesi ve Tamirat Yöntemleri
By A.H. DincerPetrol üretim sahalarında kullanılan üretim borularının(tubing) ve pompa rodlarının(sucker rod) muayenesi ile kusurlu boru ve rodların ayrılması için Sonsan Ltd.Şti. bünyesinde yaptığımız Ar-Ge sonucunda hızlı ve güvenilir bir yöntem geliştirilmiştir. Bu çalışmada bu yöntemin özellikleri ve bu şekilde kusurları tesbit edilen boru ve rodlar için uygulanabilecek tamiratlar hakkında bilgi sunulmaktadır.
-
-
-
Karşılıklı kuyu sismik kırılma verilerinin 2-B ters çözümü için yeni bir algoritma ve ilksel sonuçlar
Authors İ. Demirci and Ü. DikmenKarşılıklı kuyu sismik kırılma verilerinin iki-boyutlu ters çözümünü yapan yeni bir algoritma geliştirilmiştir. Geliştirilen ters çözüm algoritmasının düz çözüm bölümünde Hızlı İlerleme Yönteminde köşegen elemanları da kullanan bir yöntem kullanılmıştır. Bu kullanım sayesinde köşegen yönündeki hesaplama hataları minimize edilmiştir. Geliştirilen ters çözüm algoritması yapay veriler kullanılarak test edilmiş ve ilksel sonuçları sunulmuştur. Anahtar Kelimeler: Karşılıklı Kuyu, Sismik, Hızlı İlerleme Yöntemi, Ters Çözüm
-
-
-
Simultaneous vibroseis 3D seismic data recording for optimum field development-HFVS 3D seismic data acquisition and processing
Authors Y. Sakallıoglu and Z. HengThis case study presents a simultaneous vibroseis data recording and processing techniques for optimum field development in Libya. In order to acquire high trace density and high resolution 3D seismic data, the first High Fidelity Vibratory Seismic (HFVSSM) survey carried out in Libya in 2008. HFVS is an Exxon Mobil patented method that has been licensed by a number of contractors which technique allows data from multiple vibratory sources to be simultaneously recorded during the acquisition phase and separated in the processing stage. Besides the HFVS method requires one or more individual vibrators comprise a vibrator set and the recording of vibrator motion signals on each vibrator for every sweep that these actual motion signals can be used to process the data. The HFVS point source/receiver recording technique is providing high productivity and high resolution data. Processing records as unique source points allows for correction of intra array statics and differential velocity move-out which would not be possible with conventional recording where vibrator arrays are summed in the field. Measured vibrators ground force signals are used for the data inversion and separation provide more reliable data. Additionally, denser 3D geometry leads to finer spatial sampling to avoid aliasing problem and increase resolution. HFVS 3D data recording is different than conventional.
-
-
-
Geophysical infill management for improving the efficiency of marine seismic surveys
Authors P. Fontana and B. DonnellyThe marine streamer seismic acquisition method is the dominant and most cost-effective technique for acquiring seismic data in the marine environment. In a relatively short space of time the method has progressed from using single short streamers with low volume airgun sources to multi-streamer, multi-source and indeed multi-vessel arrays, which can rapidly sweep up data over vast areas.
-
-
-
Sismik yansıma yönteminde atış ve grup aralığının seçiminin önemi
Authors OO.rhan Güreli and Y. SakallıoğluSismik yansıma yönteminin en önemli parametrelerin başında: alıcı, atış grup aralığı, ofset, fold sayısı ve aktif kanal sayısı gelir. Alıcı aralığını, tabaka eğimi, ortamın hızı ve maksimum frekans kontrol eder. Eğer hesaplanan alıcı aralığından daha büyük bir alıcı aralığı seçilirse, toplanan verilerde frekans katlanması (aliasing) oluşmaya başlar. Frekans katlanması oluşmuş verilerde normalden daha düşük frekanslar gözlenir. Atış aralığı da en az alıcı aralığı kadar önemlidir. Bu sunuda, 5-m alıcı ve atış grup aralıkları kullanılarak toplanmış verilerin 10-m, 15-m, 20-m, 25-m, 30-m gibi daha geniş arlıklara dönüştürülmesi ile oluşturulmuş yığma kesitleri kesitlerinin sonuçları tartışılacaktır.
-
-
-
Güncel veri toplama tekniklerinden Nar Modelinin geliştirilmesi: Nar Modeli-II
Authors H.S. Basar, O. Güreli and Y. SakallıoğluNar modeli, iki boyutlu sismik yöntemde sinyal/gurultu oraninin ve buna bagli olarak sismik veri kalitesinin arttırılması amacı ile geliştirilmişti. Nar Modeli-II ile veri işlemin imkanlarından faydalanılarak sismik kalitenin daha da artirilmasi ve sismik kesitlerde goruntulemeinin netlesmesi sağlanmıştır. Nar Modeli-II›nin verimli bir şekilde uygulanabilmesi için ilk Nar Model`inde olduğu gibi veri toplama parametrelerinin modele uygun tasarlanmış olması gerekir. Yöntemin çalışma prensibi; saha kayitlarinin kayan ortalama methodu ile yığma işlemine tabi tutulmasi ve elde edilen yeni kayıtlara tekrar kayan ortalama islemi yapilarak yığma işlemininin en son saha verisini elde edene kadar devam ettirilmesine dayanir.
-
-
-
2D Elastic Wavefield Modeling of a Near-surface Scatterer
Authors Y. Fazelian, A. Kaslilar and U. Harmankaya2D elastic finite difference modeling is performed to obtain a shot record of a near-surface scatterer (cavity). The geometry and the physical parameters obtained from a real seismic data are used in the modeling. For simplicity and hence to have a better understanding, first a cavity embedded to a half space and then to a one-layered medium is considered. The effect of a cavity on the calculated snapshots of wavefield and on seismograms are investigated and compared with the real data.
-
-
-
Batı Raman Petrol Üretimini Artırma Projesi’nin Çeyrek Yüzyılı
More LessBu makalede, Batı Raman ağır petrol sahasında 1986 yılında karbondioksit (CO2) enjeksiyonu ile başlayan üretim artırma çalışmalarının günümüze kadar olan gelişiminden bahsedilmektedir. 1,85 milyar varil yerinde petrol rezervi olan Batı Raman sahasında 1986 yılına kadar birincil yöntemler ile gerçekleşen kurtarım sadece %1,7 iken CO2 enjeksiyonu uygulaması neticesinde 2012 sonu itibarıyla % 6 seviyesine ulaşmıştır. Rezervuarın kılcal çatlaklı yapısı CO2’in süpürme verimliliğini olumsuz etkilemektedir. Bu etkiyi iyileştirmeye yönelik çeşitli konformans (conformance) artırıcı uygulamalar denenmektedir. Ayrıca gelişen yönlü sondaj teknolojilerinden de yararlanılarak farklı profillerde kuyular kazılmakta ve kurtarım maksimize edilmeye çalışılmaktadır. Projenin olgunluk safhasındaki bölgeleri için matriksteki petrolü hedefleyen farklı bir mekanizma ile üretime devam edilmesi gerekliliği belirlenmiş ve bu konuda çalışmalara başlanılmıştır.
-
-
-
Raman Sahasında 102 Kuyuda Yapılan Su Gelişini Engelleyici Jel Enjeksiyonu Operasyonu Değerlendirmesi
Authors M. Demir, Ö. Eriçok, U. Karabakal, F. Kardaş, H. Kaya and Y. DemirelGüneydoğu bölgesinde yer alan Türkiye’nin ilk petrol keşif ve 2. büyük sahası olan Raman Sahası doğal çatlaklı kireçtaşı rezervuara sahiptir. 18 API gravitede petrol üretilen sahada üretim mekanizması aktif su itimidir. Şubat 2013 tarihinde sahada yaklaşık 190 üretim kuyusundan ortalama 6,150 v/g debi ile günlük petrol üretimine devam edilmektedir. Rezervuarda üretim zonu ile akifer arasını bağlayan doğal çatlaklar bulunmaktatır. 1990 sonrası sahada yüksek debili pompaların da kullanımının başlaması ile birlikte petrol üretiminin yanısıra su oranı da hızla artarak % 90’ı geçmiş durumdadır. Kuyularda artan bu su oranını düşürebilmek amacı ile son zamanlarda artarak yaygınlaşan, çatlaklara nüfuz ederek akiferden su gelişini engellemeye yönelik polimer jel enjeksiyonu operasyonları yapılmaktadır. Raman Sahasında ilk olarak Eylül 2007 tarihinde 7 kuyuda su gelişini engelleyici polimer jel enjeksiyonu operasyonu pilot olarak uygulanmıştır. Uygulama sonucunun başarılı olduğunun görülmesi üzerine uygulama tüm sahaya yayılarak devam etmiş ve 2012 yılı sonuna kadar toplam 102 kuyuda 107 uygulama gerçekleştirilmiştir. Uygulama yapılan kuyulardan 2012 yılı sonuna kadar yaklaşık 1 milyon varil ek üretim sağlanmıştır. Sahada başarılı su gelişini engelleyici polimer jel enjeksiyonu saha uygulamalarına önümüzdeki yıllarda da devam edilecektir.
-
-
-
Well Screening Criteria For Water Shut-Off Polymer Gel Injection In Carbonate Medium
Authors S. Canbolat and M. ParlaktunaHigh water production in oil fields is one of the major difficulties for the petroleum industry, as reservoirs become mature. Costs of lifting, handling, separation and disposal of large amounts of produced water; environmental concerns about this water; increased corrosion rates; higher tendency for emulsion; and, scale formation are among the main problems due to water production which often decrease the economic life of a well. Therefore, there is a need to reduce excessive water production. WSO polymer gel injection is a successful method for naturally fractured reservoirs which generally exhibits extreme water cut values. Gels are used in carbonate reservoirs that are dominated by secondary porosity features. This technology will preferentially flow into these features and selectively reduce permeability to water. Success of the application is based on the proper selection of the wells. Currently, gel polymer treatments have an 85-90% success rate in reducing water production and, in many cases, increasing oil production. Gel polymer systems have a penetration property greater than the mechanical methods and cement to provide a deeper barrier against the excess water. Also, plugging due to gel polymers can be removed unlike physical cement plugging which leads to a permanent plug in the porous media. The residual oil cannot be produced from the treated region by cementing method after decreasing of excess water production. The production well treatment involves injection of the gellant into the fractures or high permeability zones that produces a lot of water, thereby reducing oil production. This application not only improves draw-down from the productive zones; but, it also reduces or eliminates the costs associated with the produced water. Candidate Field for WSO application is located in southeastern Turkey which is an anticline structure. The field was discovered in January 1990 and has been on production since 1990. The structural contour map top of D formation is given in Figure.1. The field is a typical carbonate reservoir with primary drive mechanism of bottom water drive. Four formation (Zone-A,B,C and D) are oil bearing throughout the field. Zone-A is dominantly mud-stone. The formation is not expected to have matrix porosity or inter-granular porosity. Accordingly they can act as seal. Fracture porosity is present but limited, mostly in microfracture type and adds limited reserve potential when compared to the reserves created by matrix and intergranular porosity. However, permeability created by fractures is potentially very high. Zone-B is an organic rich limestone and may also act as a seal. Zone-C is a limestone. Upper part of C formation (K-C member) is also reservoir (in quality) with its porosity and permeability values. Zone-D is a limestone-dolomite formation. Zone-D which has a good secondary porosity developed by fresh water leaching and dolomitization.
-
-
-
The Effect of Clay Minerals of Reservoir Formations on Chemical and Rheological Properties of Heavy Oil by Steam Distillation
Authors Y.T. Osgouei, M. Parlaktuna and Ş. DemirciAn experimental study was carried out to investigate the role of various clay and non-clay minerals present in carbonate formations on steam distillation process. Dead oils samples (100 g) of two heavy oil reservoirs from Southeastern Turkey with 30 g water and 10 g crushed rock (limestone + mineral) were kept under steam pressure in a batch autoclave reactor for a period of 40 hours, and the results were compared as the changes in the density, viscosity and chemical composition (SARA). Three different minerals (bentonite, kaolinite, and zeolite) were added to the crushed limestone to observe their effects on the rheological and compositional changes during steam distillation process. The results of this experimental study showed that minerals have catalytic effect during steam distillation. Along with the increase in viscosity and density of remaining oil after steam distillation the chemical composition also changes. There is an increase in the asphaltene content while concentration of polar compounds decrease as the result of steam distillation.
-
-
-
Experimental and Simulation Study of Matrix Fracture Interaction in Sandstone Core Samples by CO2, CH4 And N2 Injection
Authors S. Bülbül and M. ParlaktunaIn this study, it is aimed at investigating matrixfracture interaction mechanisms with gas injection in a fractured sandstone core system. Influence of a fracture on matrix-fracture interaction processes and effects of type of the gas injected (namely, carbon dioxide, methane and nitrogen), initial gas saturation and diffusion coefficient in terms of oil recovery are studied by an experimental and simulation work. Gas oil gravity drainage and diffusion mechanisms are studied by introducing CO2, N2 and CH4 gases to the system and obtaining corresponding oil recoveries with time. An artificial fracture is created around Berea sandstone cores and system is kept at a pressure of 250 psi and at a reservoir temperature of 70 °C. n-decane is used as the oil phase. Experiments carried out with CO2 injection has resulted in higher oil recoveries than experiments carried out with CH4 and N2 respectively. It is obtained that availability of initial gas saturation in matrix increased recovery in CO2 experiments. A simulation study is also carried out to compare experimental results using CMG (Computer Modeling Group Ltd.) WinProp (Microsoft Windows™ based Phase-Behavior and Fluid Property Program) and GEM (Generalized Equation-of-State Model Compositional Reservoir Simulator) on a core scale basis. Keyword: Matrix-Fracture Interaction, Gas-Oil Gravity Drainage, Diffusion, CO2, N2 and Methane Injection, Oil Recovery
-
-
-
Küresel ısınma problemleri gölgesinde Batı Raman karbondioksit “recycle” sistemlerine bakış
More LessKarbondioksitin (CO2) petrol sahalarına enjeksiyonu, petrol endüstrisince bilinen bir uygulama olup CO2 enjeksiyonu yoluyla petrol üretiminin artırılması projesi çeyrek yüzyılı aşkın bir süredir Batı Raman sahasında başarı ile uygulanmaktadır. Proje öncesi 1.500 STBD düzeyinde olan saha üretimi proje performansının en iyi olduğu dönemlerde 8-9 kat artışla 14.000 STBD düzeyine ulaşmış, izleyen dönemde ise düşüş eğilimine girilmiştir. Buna karşın, bir varil artı petrol üretimi için rezervuara basılması gereken CO2 miktarı kontrol edilmediği takdirde artma eğiliminde olup üretilen gaz petrol oranı, rezervuar “konformans”ını arttıran su, jel vb. akışkanların rezervuara enjeksiyonu ve değişik işletme teknikleri ile kontrol altına alınmaya çalışılmaktadır. CO2 enjeksiyonunun durdurulması halinde, bilinen tekniklerle sahanın ekonomik anlamda üretilebilme olasılığı azalacağından gaz enjeksiyonu sürecinin olabildiğince uzatılması gerekmektedir. Bununla beraber, çevresel kaygılar nedeniyle petrol ile birlikte geri üretilen gazın tekrar rezervuara basılarak CO2 kayıplarının/emisyonunun en alt seviyeye çekilmesi konusu TPAO yönetimince öncelikli bir tercih olarak benimsenmiştir. Bu kapsamda, petrol ile birlikte geri üretilen gazın rezervuara yeniden enjeksiyonu amacıyla 1991-93 yılları arasında sahanın batı bölgesinde 20 MMSCFD kapasiteli ilk gaz “recycle” istasyonu kurulmuştur. Sahanın batı ve orta bölgelerinde üretilen gazın bir bölümü bu sistemle rezervuara basılmaktadır. Sahanın geriye kalan bölümlerinde üretilerek atmosfere atılmakta olan gazı toplayıp, çevrime yeniden döndürecek 20 MMSCFD kapasiteli ikinci bir tesis de sahanın doğu bölgesinde kurularak 2009 yılı başında devreye alınmıştır. 2012 yılında ilk “recycle” istasyonunun kapasitesi yeni kompresörlerin ilavesi ile 20 MMSCFD artırılarak sahada üretilen tüm gaz geri basılması mümkün hale gelmiştir. Bu bildiride, CO2’in çevresel etkileri ve sözü edilen gaz “recyle” sistemlerinin kurulum gerekçeleri irdelenerek, sistemlere ilişkin teknik bilgiler verilmekte, süreçler anlatılmaktadır.
-
-
-
Micro scale sweep visualization experiments using carbonate samples
Authors M.T. Khan, M. Zeytçioğlu and S. SanerMicroscopic visualization can provide valuable information to enhance the understanding of porescale transport phenomenon. This research provides insights which may support numerical flow simulations in microscopic scale displacement processes using a two dimensional (2D) micromodel. The visuals were recorded and analyzed to investigate as to how the sweep efficiency in carbonate reservoir rock samples varies with different displacing liquids. Crucial observations and results were attained for better understanding of the flooding practices conducted at the field scale.
-
-
-
Reflecting Risks and Uncertainties in Reserves Estimations Using Reserves Classification Frameworks
Authors M.F. Tuğan, M. Onur and M. YılmazThe main target of all shareholders is to increase their income by producing oil and/or gas. The key parameter to produce oil and/or gas is the investments, such as purchasing licences, drilling wells, and constructing production facilities. Oil companies program their investments to a particular field by analyzing the ultimate recovery from that field, i.e. have to know their reserves and the associated risks and uncertainties. To have a better understanding on the risks and uncertainties in estimated results, resources are classified using international or local frameworks. This work will examine the two most widely used international frameworks (SPE-PRMS and UNFC), basic concepts concerning them.
-
-
-
Beypazarı (Ankara) Trona Çözelti Madenciliği Projesinde Kuyu Loglari ile Formasyon Değerlendirme, Cevher Karakterizasyonu ve Kavernaların İzlenmesi
Authors G. Çakmakçı and L. VranaBeypazarı Trona Çözelti Madeni, aşağıda sıralanan nitelikleri ile ülkemizde ve dünyada biricik kabul edilmektedir: 1- Tamamen bakir bir yatak üzerinde, çözelti madenciliği yöntemi ile işletilen, dünyanın iki trona madeninden büyük olanıdır. Diğeri Wucheng’de (Henan Eyaleti/Çin) yer almakta olup, dik şekilde açılan kuyular hidrolik çatlatma tekniği ile ilişkilendirilmektedir. 2- Eşzamanlı işletilen kuyu/ünite sayısı ile dünyanın en büyük çözelti madenidir. 122 adet aktif kuyu olup, bu sayı kısa süre içinde 148’e yükselecektir. Bu sayıdaki kuyuya karşılık gelen aktif ünite sayısı ise 55 olacaktır. Yatak cevherleşme alanı 230-530 m. derinlikte yer almaktadır. Şu anda 120000 varil/gün trona çözeltisi üretilerek tesislerde buharlaştırma yöntemi ile günde 3600 ton Soda külü üretilmektedir. 3- Yerüstü teşkilatı (yol, boru ve otomasyon ağı) ile dünyanın en büyük çözelti madenciliği sistemine sahiptir. Toplam, 2 km2’lik bir alanda yaklaşık 20km’lik bir yol ağına paralel, 43km civarında bir boru ağı bulunmaktadır. 4- Yönlü sondaj teknolojisinin ülkemizde bir madencilik çalışmasında kullanıldığı ilk işletmedir. Aslında yönlü sondaj tekniği ile inşa edilen ünitelerin yer aldığı dünyanın tek trona çözelti madenidir. Projenin etüt ve fizibilite çalışmaları 1998 yılında başlamasına karşın, konvansiyonel madencilik yaklaşımının getirdiği birtakım belirsizlikler nedeniyle araştırmalara devam edilmiş, sonuçta çözelti madenciliği uygulanmasına karar verilmiştir.
-
-
-
Adıyaman ve Batman Sahalarında Radyal Drilling Operasyonu Değerlendirmesi
By S. ÖztelRadyal Sondaj teknolojisi genel olarak jetleme kuvvetini kullanarak casing indirilmiş veya açık olarak tamamlanmış kuyu fark etmeksizin formasyonda yatay olarak penetrasyon sağlamaktır. Bu ilerleme ilk olarak coiled tubing, PDM tipi motorlar, Matkap ve bükülebilir bir shaft kullanılıp casing›de 2.5 cm çapında bir delik açılarak yapılır. Gerçek penetrasyon kevral tipi yüksek basınçlı bir hortumun ucundaki bir jet ve coiled tubing kullanılarak yapılır. Yüksek basınç kullanılarak ön ve arka jet deliklerinde oluşan kuvvetler a) Formasyonda hidrolik patlatma ve erezyonal kuvvetleri kullanarak formasyonu delme ve b) ters hidrolik kuvveti kullanarak kendini formasyon içine ilerleme ve yataysallığı sağlar. Bu bildiride Türkiye›de uygulanan radyal sondaj operasyonları şu başlıklar da değerlendirilecektir. 1. genel bilgiler 2. Teknik faydaları 3. Radyal sondajın katkıları 4. Operasyonel açıdan çıkarılan dersler 5. Saha sonuçları 6. Sonuç
-
-
-
Neural Network Applications of Seismic Attributes for Predicting Porosity and Production
By U. ÇelikThe introduction of seismic attributes to the exploration world has brought another dimension to the seismic data interpretation. Further development has introduced another approach known as multi-attribute analysis which uses artificial neural networks (ANNs) to combine the multiple attributes to predict desired reservoir properties. Seismic attribute analysis using neural network applications has become an important tool for understanding the physical features and internal structure of reservoirs. Understanding such features is vital to provide effective strategies for exploration and exploitation in both new and old survey areas.
-
-
-
Goins ve Lubinski Yöntemleri ile Koruma Borusu Oturtma Pratiği
Authors G. Altun, M. Hakan Özyurtkan, İ.M. Mıhçakan and U. SerpenKoruma borusu yerleştirme ve çimentolama sondaj operasyonlarının en önemli aşamaları arasındadır. Kuyuların giderek daha derinlere delinmesi beraberinde farklı sorunlar getirmekte ve bu sorunlara mühendislik çözümleri bulunması gerekmektedir. Derin kuyulara indirilen farklı kalitedeki ve/veya birim ağırlığıktaki koruma boruları genel bir yaklaşımla bütünüyle çimentolanmakla, ancak çeşitli teknik nedenler ve ekonomik olmasından dolayı dizinin kısmî çimentolanması da yaygın uygulanmaktadır. Koruma borusunun kısmi çimentolanması olarak bilinen “koruma borusu oturtma”, endüstri tarafından çok farklı yöntemler kullanılarak uygulanmaktadır. Dizinin kuyu başında hangi eksenel gerilme ile oturtulacağının belirlenmesi için kabul görmüş bir yöntem yoktur. Ancak, oturtma yüklerinin analizinde konservatif oturtma gerilmelerini hesaplayan Lubinski yöntemi ile, grafiksel hesaplama sağlayan Goins yöntemi yaygın olarak kullanılmaktadır. Bu çalışmada, koruma borusu oturtma konusu genel anlamda tanıtılmakta, gerekli yüklerin hesaplanmasında kullanılan Lubinski ve Goins yöntemleri örnek bir kuyu için uygulamalı olarak verilmekte, elde edilen sonuçlar karşılaştırılarak iki yöntemden elde edilen sonuçlar arasındaki farklılık ayrıntılı olarak açıklanmaktadır.
-
-
-
A Simulation Study of Immiscible CO2 WAG Injection in the Bati Kozluca Heavy Oil Field
More LessBati Kozluca field is a heavy oil carbonate reservoir discovered in 1984; it is located in the South East of Turkey, close to Syria border. The reservoir began primary production in 1985, developed with 41 wells producing 12 API oil. The permeability and porosity are 500 mD and 25% respectively. Reservoir depth is up to 1520 m and the original reservoir pressure is 2000 psia. Reservoir thickness is 133 m with 17% of net to gross ratio. Main constraints for oil recovery of the field are the high viscosity and low aquifer support. To increase the oil recovery, reservoir management and re-evaluation studies started in 2000. First EOR methods were screened and it was decided to apply immiscible CO2 injection. There is a CO2 reservoir at Camurlu Field which is 10 km away from the Bati Kozluca Field so that CO2 injection method has the priority among other EOR methods. In 2003, immiscible CO2 injection was started to increase the oil recovery. Until 2007, immiscible CO2 injection had been continued. However, the increase in the recovery was limited because of the quick breakthrough and adverse mobility ratio between CO2 and oil. In 2007, to overcome the problems associated with the mobility ratio, water alternating CO2 injection was started. According to results, oil recovery increased and also water and gas production decreased after applying WAG method. This paper describes the field-wide simulation study conducted to predict the future reservoir performance of the black oil simulation model under various operating and development strategies. Firstly, available data is screened and quality of the data is evaluated and then the model is history-matched on both the field and the well scale. Continuous CO2 injection and WAG methods are considered and WAG method is found the most favorable method to increase the oil recovery and to decrease the amount of CO2 injected.
-
-
-
Reservoir Simulation Study of Bozova Oil Field
Authors M.C. Ertürk and M. YılmazBozova Oil Field, with 1.4 km2 area, is located in the southeastern part of Turkey. Reservoir thickness ranges 27 to 40 m with 60 % of net to gross ratio and it is found at depth around 2400 m. In terms of quality, the reservoir has moderate porosity, low permeability, and water and compaction drive mechanisms with an average oil density of 23 API and initial pressure of 2550 psia. To date, 8 wells have been drilled, 4 of which are active and production accumulated throughout 18 years amounts approximately 1.6 million barrels. The purpose of the study is to improve a full-field reservoir simulation for Bozova field including data review, history matching and production forecast. The first step of that is quality-checked of geologic model to accept it for commencing of the simulation project. In the next step, scrutinizing of available PVT and petrophysical data as input is essential part to honor the reservoir system in a proper way. After initialization of the base case, calibration of reservoir simulation model to the historical production data is a required step before a reservoir model can be utilized for making predictions of the future performance of the reservoir. In the study, several development strategies were simulated by launching do nothing case, additional new wells, and waterflooding case. As a result, all those forecasts will give us insight into different approaches and the result of alternative applications causing production increasing in Bozova field.
-
-
-
Eksik Verili Rezervuar Karakterizasyonu Problemlerinde Kısmi Çifte Olasılıklı Parametre Tahmin Yönteminin Kullanımı
Authors M.D. Paker and M. OnurYeraltı petrol/doğal gaz rezerv tespitleri ve üretim planlamaları yapmak için, incelenmekte olan gerçek rezervuar sistemini yansıtan bir rezervuar modeli oluşturmak gerekmektedir. Bu rezervuar modeli genellikle statik (log ve karot gibi) ve dinamik (üretim ve kuyu testleri gibi) veriler ile oluşturulup, düzenlenmektedir. Gözlenen statik verilere bağlı rezervuar karakterizasyonu genellikle doğrusal tahmin problemi iken, gözlenen dinamik verilere bağlı rezervuar karakterizasyonu doğrusal olmayan tahmin problemidir. Doğrusal ve doğrusal olmayan tahmin yöntemleri eldeki veri (veya denklem) ve bilinmeyen parametre sayısına bağlı olarak eksik ve artık verili olarak sınıflandırılır. Eksik verili problemlerde, tahmin edilecek bilinmeyen rezervuar parametre sayısı gözlenen uygun veri sayısından fazladır. Halbuki artık verili problemlerde, gözlenen uygun verisi sayısı tahmin edilecek bilinmeyen parametre sayısından fazladır. Ancak, iyi bir rezervuar modeli oluşturmada, özellikle eksik verili problem çözümlemesi söz konusu olduğunda, tek başına statik ve/veya dinamik olarak ölçülen veriler yeterli olmamaktadır. Bu verilerin yanında, rezervuar parametrelerinin doğrusal ve doğrusal olmayan metotlarla güvenilir olarak tahmin edilmesinde, bu parametrelere ait önsel bir model eklemek yararlı olmaktadır. Önsel model, kişinin önsel ortalama ve rezervuar parametrelerinin (geçirgenlik, gözeneklilik, faya olan uzaklık gibi) üzerindeki belirsizlik hakkındaki bilgisini göstermektedir. Ama tahminlerde önsel model kullanmak model parametrelerinin yanlı bulunmasına da neden olabilmektedir. Eğer verilen önsel ortalama yanlış ya da belirsiz ise parametrelerin değerleri de oldukça yanlış tahmin edilebilmektedir. Bu çalışmada, Bayes teoremi kapsamında kısmi çifte olasılık parametre tahmin yöntemi ile önsel model parametrelerinin üzerindeki hatanın eksik verili rezervuar karakterizasyonu problemlerindeki etkisi araştırılmıştır. Araştırmada, eksik verili doğrusal problemler için statik verilerden yararlanarak oluşturulan önsel bir boyutlu (1B) bir jeoistatistiksel rezervuar modeli göz önünde bulundurulmuştur. Doğrusal tahmin problemleri için oluşturulan olasılık yoğunluk fonksiyonlarından (oyf) uygun hedef fonksiyonları türetilmiştir. Bu çalışma kapsamında kullanılan parçalı çifte olasılık parametre tahmin yönteminden elde edilen sonuçlar, önsel bilgiyi kullanmayan alışılagelmiş en küçük kareler ve maksimum olasılık yöntemleri ile karşılaştırılmıştır. Sonuçlar önsel bilginin yanlış olması durumunda, parametrelerin önsel ortalamaları üzerindeki hataları dikkate almayan alışılagelmiş metotlara nazaran, kısmi çifte olasılık parametre tahmin yönteminin daha doğru bir rezervuar karakterizasyonu sağladığı göstermiştir. Ayrıca, bu yöntemin, parametrelerin önsel ortalamalarının belirsiz olması durumunda da oldukça etkin olduğu görülmüştür.
-
-
-
Numerical simulation of two-phase oil and water flow
Authors A. Sever, Ö.İ. Türeyen and M. Onurmethods. However, there exist numerous articles that attempt to develop and present analytical solutions in the literature for the two-phase flow of oil and water under some restricted assumptions (e.g., homogenous reservoir). Analytical solutions may be easy and fast to apply, but may not well represent the oil and water flow because of their restrictive assumptions. On the other hand, numerical methods are more appealing to solve the oil and water phase flow for more general cases. Due to its generality, in this study, we consider numerical based methods (i.e., finite difference methods) to solve the diffusivity equation for oil-water flow and investigate the pressure and water saturation behaviors of a vertical well and reservoir for the cases where analytical solutions are not available. A general discretized equationis derived for simulating two-phase water and oil flow in three-dimensional (3-D) r-θ-z cylindrical coordinate system using the finite difference method. Then, this general difference equation is solved by considering two different methods. The first method is based on a fully implicit solution of both pressure and saturation (FIMPS) using the Newton method, and the other method is based on a fully implicity solution of pressure and explicit solution of saturation, which is known as the IMPES method. Derivations for both methods are given in this study. The solutions generated from the simulators developed during the course of this work were compared and validated with the solutions generated from a commericial software CMG - IMEX.Moreover, we also validate the simulator for some benchamark cases taken from the papers presented in the literature. Finally, some well-test applications are run with the simulator and pressure differences and their derivatives (diagnostic plots) are analyzed. This process is achieved with the commercial well-test software ECRIN. Behaviour and effects of mechanical skin on diagnostic plots for injection and fall-off tests are discussed.
-
-
-
A numerical study of the pressure behavior of a vertical well in a dry gas reservoir
Authors C. Alan, Ö.İ. Türeyen and M. OnurPredicting production performance of a dry gas reservoir for reservoir management acquires understanding the behavior of pressure transients and fluid distribution over both space and time. In recent years, reservoir simulators have been extensively used to build various reservoir and well models to investigate and visualize the process under a series of potential scenarios, such as drilling new wells and injecting fluids. The objective of this study is to develop and present applications of a general purpose two-dimensional (2D) r-z, fully implicit, single-phase, real gas simulation model with a single well located at the center of a cylindrical reservoir. The simulation model includes wellbore storage, skin and non-Darcy flow effects. As the problem is non-linear, solve pressures at each gridblock at a specific time may require more than one iteration. Since two different methods called as functional iteration and Newton’s methods are applicable to solve such systems, they are analyzed, verified using at least two different solvers with respect to accuracy and speed. The simulator is verified by a well-known well test analysis software to perform a number of real field applications such as standard and routine tests of natural gas industry (i.e., flow-afterflow, isochronal and modified isochronal tests) for both partially and fully penetrated wells either in a single or multilayered systems. The simulator is also capable of conducting a packer-probe test called as Mini-Drill Stem Test (MiniDST) for estimation of reservoir properties such as permeability, skin, etc. The effect of Non-Darcy flow on pressure solutions at the tested well as well as throughout the reservoir for the entire flow rate history is also investigated in a different manner than described in mathematical formulation such that the a non-Darcy flow area in radial direction is introduced and restricted to a region of a specific radius which is concentric with wellbore.
-
-
-
Kuzey Marmara Field: Seismic to Simulation Study
Authors D. Yıldırım, C. Çetinkaya, İ.P. Hacıköylü, M.Z. Alper, A. Yılmaz, M. Akpınar, Y. Karakeçe and M. YılmazKuzey Marmara offshore sahası 1988 yılında keşfedilmiştir. 2007 yılına kadar 2.2 milyar Sm3 gaz üretildikten sonra Nisan 2007’de sahada gaz depolama operasyonları başlatılmıştır. Bu güne kadar 6 adet başarılı depolama dönemi gerçekleştirilmiştir. Sahada yeni kuyuların kazılması yoluyla çalışma gazı kapasitesinin artırılması gündeme gelmiş ve bu amaçla optimum kuyu sayısı ve kuyu lokasyonlarını belirlemek üzere sismikten simülasyona geniş kapsamlı bir çalışma gerçekleştirilmiştir. Bu kapsamda farklı disiplinlerden oluşan bir TPAO ekibi oluşturulmuş ve yabancı bir mühendislik firması ile birlikte bu çalışma yürütülmüştür. Çalışmadan elde edilen sonuçlar kapasite artırım çalışmalarının dizayn kriterlerini belirlemeye ışık tutmuştur. Çalışma iki fazda yürütülmüştür. Faz 1 jeolojik model ve temel mühendsilik çalışmalarını kapsamaktadır. Jeofizik, jeolojik, petrofizik ve rezervuar mühendisliği disiplinleri aracılığı ile detaylı bir rezervuar tanımlamasına gidilmiş ve neticesinde 3 boyutlu bir jeolojik model oluşturulmuştur. 30x30x1 m hücre boyutlarında 1,891,000 aktif hücre ile jeolojik model oluşturulmuş ve upscaling ile simülasyon çalışmalarında kullanılmak üzere daha büyük boyutlarda ve daha az aktif hücre sayısına sahip bir modele geçilmiştir ( 90x90x1.7 m ve 113,000 aktif hücre). Gözeneklilik logları upscale edilerek Gaussian random function simülasyonu ile modelleme yapılmıştır. Modellemede her layerda fasiyes zonlarına koşullandırma sağlanmıştır. 3D pre-stack sismik ters çözümlemesinden elde edilen impedance ise co-krigging işleminde ikincil parameter olarak kullanılmıştır. Rezervuar simülasyonu çalışmanın ikinci fazını oluşturmuştur. Kütle denge çalışması hacimsel çalışma ile uyumlu bulunmuştur. Model geçmiş üretim ve depolama senaryolarının tarihçe çakıştırması ile doğrulanmıştır. Performans tahmin çalışmalarında ise çeşitli senaryolar oluşturulmuş ve en iyi çözümü sağlayacak kuyu adedi ve bu kuyuların nereden kazılması gerektiği belirlenmeye çalışılmıştır. Simülasyon modelinde 2 adet merkez platformdan veya 2 adet kenar platformdan kuyular açılmış ve değerlendirmeler yapılmıştır. 12, 16 ve 18 ek kuyu açılması durumlarında ve 42 milyon Sm3/d gaz üretimi sağlanacak şekilde simülasyonlar gerçekleştirilmiştir. Çalışma gazı yaklaşık 3,700 million Sm3, çalışma gazının toplam gaza oranı % 65-66 olarak gerçekleşmiştir. Tahmin edilen performanslara göre kuyuların merkezden veya kenardan açılmasında benzer sonuçlar elde edilmiştir. Tercih edilecek platform lokasyonlarında belirleyici unsurun sondajların kolaylığı ve kıyı boru hattı bağlantılarında avantaj sağlayacak dizaynların olduğu sonucu çıkarılmıştır.
-
-
-
Production Performance Analysis of Coal Bed Methane, Shale Gas, and Tight Gas Reservoirs with Different Well Trajectories and Completion Techniques
Authors M.C. Ertürk and Ç. SinayuçThe vast majority of gas production all over the world comes from conventional reservoirs that become ever-increasingly difficult to discover and exploit. However, business cycles and higher gas prices affect and change the gas production strategy of the industry. Concordantly, the significance of unconventional gas reservoirs has been increasing for recent years owing to economic viability of their development and, therefore identification of the challenges and common pitfalls regarding those have been gaining importance at the same time. In the last decades, the exploitation of unconventional gas reservoirs such as coalbed methane, shale gas, and tight gas has become an ever increasing part of world gas supply. With state of the art technology and high gas prices, these resources can be developed by achieving economical gas production. The economic viability of many unconventional gas developments hinges on effective stimulation of extremely low permeability rock by creating very complex well trajectories and fracture networks. Generally, unconventional gas reservoirs are described as having very large hydrocarbon reserves in place, a low expected ultimate recovery, and low permeability. These reservoirs cannot provide efficient amount of gas with an economical rate and they require some special stimulation treatment techniques. Mostly, horizontal wells or multilateral wells with transverse hydraulic fractures make the feasible production rates possible, and improved performance of these reservoirs should be taken into account as much accurate as possible. Evaluation of unconventional gas reservoirs is much more challenging as compared to conventional gas reservoirs due to their complex rock properties, drilling and completion techniques, and production mechanism. Each unconventional gas reservoir is unique and needs special interests to be characterized accurately. Ordinarily, it is very difficult to characterize them and choose the right recovery techniques. Accurate stimulation and determination of the unconventional gas reservoir systems plays an important role to produce natural gas commercially and optimize the recovery properly. At this point, numerical simulation approach that is the most beneficial tool to validate and predict the performance of these kinds of systems provided that adequate and reliable data are available comes into play. Although simulation of the unconventional gas reservoirs are also challenging process due to the several reasons like ultra-low permeability, desorption, complex geological characteristics, it offers remarkable potential for understanding of unconventional gas reservoirs. The main effort of this study is to investigate the well performance of coalbed methane, shale gas, and tight gas reservoirs with different well configurations and stimulation scenarios. In order to obtain the outcome of these analyses, a 3D layered geological model with a 25x25x52 grid having four different zones with different thicknesses was constructed and modified for each reservoir system with different characteristics as a means of providing some distributed properties by Petrel. On the other hand, the reason the models were created with similar areal extend is to compare the gas in place and recovery of each system. A series of reservoir simulation were performed by Eclipse as a commercial numerical simulator with two types of porosity system; dual porosity for coalbed methane and shale gas reservoirs, single porosity for tight gas reservoir. In some reservoir systems, hydraulic fractures were represented and included into the model by local grid refinement and permeability multiplier facilities of Eclipse for vertical, horizontal, and multilateral well types.
-
-
-
Sıvının hakim olduğu jeotermal rezervuarlarda basınç ve sıcaklık davranışlarının incelenmesi
Authors Y. Palabıyık, Ö.İ. Türeyen, M. Onur and M. DenizBu çalışmada, tek-faz sıvının hakim olduğu jeotermal sistemler için basınç ve sıcaklık davranışını simüle edebilecek izotermal olmayan bir rezervuar modeli geliştirilmiştir. Model, rezervuar için kütle dengesi ve enerji dengesi denklemlerinin eş zamanlı çözümü esasına dayanmaktadır. Geliştirilen model aynı zamanda kuyu sıcaklığının gerçekçi simülasyonlarını yapabilmek için rezervuardan alt ve üst tabakalara olan ısı kayıplarını da modelleyebilmektedir. Doğrusal olmayan denklem takımları tamamen kapalı bir biçimde Newton yöntemi ile çözülmektedir. Model 2-boyutlu (r-z) silindiriktir ve bu sayede kuyu dibi sıcaklık ve basınçlarının gerçekçi tanımlamalarını sağlamaktadır. Bu modelle özellikle çalışmanın ana odak noktası olan sıcaklığın kararsız akış dönemindeki davranışları ve çeşitli formasyon ve kuyu özelliklerinin basınç ve sıcaklık davranışları üzerine etkileri çalışılmıştır. Bu çalışmada ele alınan sentetik örnekler, kuyu dibi sıcaklık davranışı üzerine gözeneklilik, zar faktörü ve geçirgenlik gibi diğer parametrelere kıyasla en çok kayaç ısıl iletkenliğinin etkisi olduğunu göstermiştir.
-
-
-
Case Study of High-Density Third Generation High- Performance Water Based Drilling Fluids Application
Authors O. Arıyan, A. Bayram, H.A. Doğan, M.G. Gökdemir, A. Kahvecioğlu and B. ŞahinThis paper presents a case study on ‘Third Generation High performance Water Based Drilling Fluid System’ application to drilling of a high pressure oil well. Recently drilled well was the highest pressurized one in the Black Sea region. Last two sections were drilled around 17 ppg drilling mud. The fluid system was not designed to be an HPHT system at the planning stage of the well, however unexpected sudden kicks has forced water based mud system to its limits in terms of density. The authors will give details about the design, fluid formulation, field trial, drilling and fluid performance.
-
-
-
Using Rock Physics and AVO tools to determine hydrocarbon bearing zones in an exploration well, Diyarbakir Basin, Southeast Turkey
Authors S. Baytok, S. Dündar, M. Mutafçılar, B. Üstün, Ş.A. Aktepe and M. KılıçayRock physics provides a good theoretical tool and understanding of the connection between the elastic parameters and the physical properties of reservoir rocks; therefore, a relationship and a link between physical rock properties and seismic expressions can be established. This study aims to utilize rock physics and AVO theoretical tools to better determine and characterize hydrocarbon-bearing zones at a newly drilled “Well-A” in Diyarbakir Basin in the southeastern Turkey. “Well-A” is located at 10 km in distance to major producing oil fields targeting limestones of Dadas Formation and sandstones of Bedinan Formations. In the vicinity of Well-A, two exploration wells were drilled before and completed as “dry well” with minor oil and gas shows. In the area, source rocks are the shales in Dadas Formation in Diyarbakir and northern Diyarbakir area and early Cretaceous age carbonates in Adiyaman area. Reservoir rocks are early Paleocene age Sinan and Garzan Formations, late Cretaceous age carbonates of Mardin Group’s Karababa and Derdere Formations, and sandstones of Paleozoic Bedinan and Hazro Formations. There has been 2 Drill Stem Tests (DST) conducted at wellbore. First DST was successful between the depths from 2755 to 2767 m (9038-9078 ft) and 81 stand (st) gas mud mixed condensed was recovered. Second DST was between 2863-2893 m (9393-9491 ft) and 28 st. recovery was made. At this point, rock physics and AVO studies are required to aid in the determination of hydrocarbon-bearing zones for perforation. Rock physics part of this study includes the calculation of elastic parameter logs. Lame constant (λ), Lambda-Rho, Shear Modulus (μ), Mu-Rho, Young’s Modulus (E), Poisson’s Ratio (σ), Bulk Modulus (k) were calculated and used to create crossplots to determine and evaluate hydrocarbon-bearing intervals. Lambda*Rho vs. Lambda/Mu, P-Impedance vs. Vp/ Vs, porosity vs. p-wave velocity, acoustic impedance vs. elastic impedance (at 30 degrees) and Vp vs. Vs crossplots were generated and examine to determine possible reservoir intervals. Specific focus has been put on Young’s Modulus (E) and Poisson’s Ratio (σ) to determine brittle and ductile zones for a future fracking operation. Shear-wave sonic log measurement plays a crucial role in the calculation of elastic parameter logs since all the equations require shear-wave velocity information.
-
-
-
An Experimental Study of Silicate-Polymer Gel Systems to Seal Shallow Water Flow and Lost Circulation Zones in Top Hole Drilling
Authors A. Ay, İ.H. Gücüyener and M.V. KökPlacement of silicate based gel systems is one of the oldest methods to seal such undesired zones. For this study, sodium-silicate based gel system is investigated experimentally. This gel system is deliberately delayed multi-component system mixed as a uniform liquid at the surface but desired to form strong gel where it is placed in the well. The experimentally analyzed system is composed of distilled water, sodiumsilicate solution, polymer solution, lost circulation materials, weighting agent and organic initiator. In this study, effect of these components on gel time, gel quality and gel strength at room temperature is investigated as a function of their concentration. To be able to compare gelation time of different compositions, gel time tests were performed by following the developed method in this study. Observation codes were defined to be able to compare the gel qualities of different compositions. For gel time and quality tests, sodium-silicate (SS) concentrations from 3.5% to 15% were studied and the concentrations between 7.5% and 10% were found as optimum. Gel time is getting higher as silicate-initiator ratio (SIR) increases for these optimum concentrations. It was also determined that, addition of polymers reduces the gel time and increases the elasticity of the resulting gels. Long term gelation process was investigated by monitoring turbidity (NTU) of the mixtures and plotting NTU versus time curves. Viscosity development curves obtained from rotational viscometer at various constant shear rates indicated reduced gelation times with increasing shear rate. Furthermore, by using modified High-Pressure, High-Temperature filter press cell, it was determined that, addition of lost circulation materials increases the extrusion pressure.
-
-
-
A study to determine the cement slurry behaviour to prevent the fluıd migration
Authors G. Karakaya and M.V. KökIn this study, the effect of free water, which is the basic quality property of API G-Class cement, on fluid migration potential has been tested for different origin Class-G cement samples (Class G-1, 2 and 3), in combination with different physical conditions. In order to justify the quality of each cement sample, standard API G-Class quality tests were performed. The free fluid values of different origin Class-G cement samples (Class G-1, 2 and 3) were determined as %2.5, %5 and %3.2 respectively. It was found that the Class G-1 cement with the lowest free fluid content has the lowest potential for fluid migration. Moreover, static gel strength analyzer (SGSA) is used to measure the static gel strength of cement slurries to determine the time to complete transition period.
-
-
-
An experimental investigation of the shale inhibition properties of a quaternary amine compound
Authors B.T. Tas, I.H. Gucuyener and M. ParlaktunaDepleting oil reserves and increased costs of the oil and gas recoveries have created the need to drill in challenging formations. When drilled through, shale formations in particular always generated a wide variety of problems if conventional water-based muds are used. Furthermore, the complexity and variations in shales have compounded the task of developing suitable drilling fluids. In light of these problems, the study of shale properties and their interactions with fluids will continue to be a much-needed source of information in drilling industry. In this study a low molecular weight quaternary amine compound, which is provided by KarKim Drilling Fluids Inc., and its mixtures with sodium and potassium chloride is investigated in the aspects of capillary suction times, hot rolling recoveries, methylene blue capacities and one-dimensional free swelling properties in order to compare performances of salts and amine compound. For all test methods quaternary amine concentration from 1% to 6% by volume were studied and seen that less amount of quaternary amine compound is needed in order to obtain close shale recoveries and shale volume change potential if compared with sodium and potassium chloride. This prevents the usage of high concentration of chlorides and hence provides environmental sensitiveness. Furthermore, it was concluded that combining an amount of salt with quaternary amine compound
-
-
-
A Review of Application of Computational Fluid Dynamics in Prediction of Oil and Gas Wells Problems
Authors A.E. Osgouei and G. AltunComputational Fluid Dynamics (CFD) is a powerful way of modeling fluid flow, heat transfer, and related processes for a wide range of important scientific and engineering problems. Unlike experiments that only permit data to be extracted at a limited number of locations in the system (e.g. pressure and temperature probes, heat flux gauges, etc.), CFD allows the analyst to examine a large number of locations in the region of interest and yields a comprehensive set of flow parameters for examination. Simply, CFD provides the ability to theoretically simulate any physical condition. Increasing demand for energy resulted in the exploration more sources and subsequently expansion of drilling activities all over the world. Any improvement in terms of well planning, drilling and production operations can result in significant saving for the operators. It is therefore crucial to have an idea and to develop efficient strategy in the case of experimentally expensive and unpredictable oil and gas wells operation in advance. CFD has the important role in petroleum engineering applications such as studying optimization of bit performance, convective heat transfer between casings and annular fluids, flow in porous media like mud filtrate invasion, simulation of multi-phase flow for designing separators, cement displacement, erosion prediction, risk analysis during blowout event, optimization of drilling hydraulics and hole cleaning, wellbore stability analysis, cutting transport in wellbore and modeling flow through whole oil and gas wells. Presented in this study is an attempt to literately summarize estimation and modeling some problems encountered in oil and gas wells during drilling and production operations. In short, this paper evaluates some certain issues in a whole well system and details the successful application of CFD techniques to model and predict these issues before any implementation in a well. Culminated results reveal that CFD analysis can provide valuable insight that helps engineers to understand what is physically happening when such above mentioned events are faced prior to any stage of oil and gas wells operations.
-
-
-
Jeotermal Kuyu Çaplarının Optimizasyonu
By U. SerpenJeotermal kuyular standard ve geniş çaplarla delinmektedir. Bu farklı çaplarla delinen kuyuların maliyetleri ciddi farklar taşımaktadır. Geniş çaplı delinen kuyular da bazan beklenen üretimler açısından hayal kırıklığı yaşatmaktadır. Bu çalışma, hangi çapların daha uygun olacağını belirlemek amacıyla gerçekleştirilmiştir. Bu amaçla, deterministik ve stokastik çalışmalarla optimum çaplar tayin edilmeye çalışılmıştır. Bunun yanında, yeraltındaki belirsizliği daha iyi değerlendirmek için bir risk analizi uygulaması yapılarak, bu çaplar farklı derinlikler için sunulmuştur.
-
-
-
Wellbore Temperature Assessment for Generic Deep Water Well in Black Sea and Mitigation of Hydrate Dissociation Risk
Authors M. Parlaktuna and M.T. ÖztürkDrilling operation expanded through deep water environments starting from mid-1980s. As drilling operations are expanded through deep water environments, hydrate forming problem is occurred as a result of low temperature and high pressure profile. This case is generally faced during production from the deep water gas wells, since during the production phase, pressure and temperature distribution through the wellbore falls on hydrate stability interval. On the other hand in the drilling & completion phase, gas generated from the shallow sediments may form hydrates in downhole equipment like; subsea well heads, hanger profiles, subsea wellhead hanger pack-offs, subsea BOP stack & BOP funnel. Moreover in case of drilling through sediments including in-situ hydrates, as drilling goes deeper, heat transfer from well target-depth through the upper well sections, with drilling fluid circulation, will occur and temperature profile through the wellbore will change. As a result of heat transfer, overheating of the shallow well bore sections become possible. In such cases wellbore stability will decrease with the dissociation of the hydrate bearing sediments for the conductor or surface casings. Also, mentioned hydrate dissociation and gas migration through the surface may cause buoyancy problems in the location and lead to the failure of the floating drilling unit, since volumetrically 1ft3 of in-situ hydrate contains as much as 170scf of gas. When considering drilling operations, hydrate forming risk can be eliminated via using kinetic or thermodynamic inhibitors in the drilling fluid system. However, at the wellbore and behind cemented casings, changes on pressure and temperature will also lead to dissociation of shallow hydrate bearing sediments. When considering regular drilling operation, severe changes on pressure profiles are not expected but heat flux from deeper sections of the well through shallower section is the major parameter which will affect hydrate stability condition on downhole. In order to mitigate the risk mentioned above, in this study, Black Sea is taken as a reference drilling environment and wellbore temperature simulations are conducted. Hydrate stability curve is determined by using the data gathered from wells drilled in the region and experimental studies conducted on hydrate existence of the Black Sea. Effect of regional parameters such as geothermal gradient of the region, target depths and operation parameters and well bore geometry changes including; hole sizes, casing shoe depths, casing specifications, circulation rates, mud weights, mud type, mud inlet and outlet temperatures are interpreted. As a result, hydrate dissociation risk for deep water well is mitigated by optimizing well geometry and operation parameters.
-
-
-
An investigation of the leak-off tests conducted in oil and natural gas wells drilled in Thrace Basin
Authors M. Parlaktuna, N. Karahanoğlu and B. KayaelThis study aims to analyze the leak-off tests carried out in the Thrace Basin of Turkey by Turkish Petroleum Corporation and find any relationship that may exist between leak-off test results and drilled formations as well as drilling parameters, such as mud weight, depth. The analysis of 78 leak-off tests indicated that there is no close correlation between the mud weight of test fluid and equivalent mud weight (fracture gradient) if the test is carried out within impermeable sections. On the other hand, the correlation between mud weight and equivalent mud weight increase while running the test within permeable-productive zones. It is also found that the leak-off test results are not dependent on the depth but the formation to be tested. The analyzed leak-off test results from Thrace Basin showed that the fracture gradient is not the limiting factor to set the casing of any section unless a gas show is observed during drilling operation which occurred only in 5 wells out of 78 wells analyzed.
-
-
-
Economical Impact of A Dual Gradient Drilling System on Drilling Cost
Authors M. Peker and M. ParlaktunaDual Gradient Drilling (DGD) system is a promising technology that was developed to overcome the deep water drilling problems occurred due to narrow operating window between pore pressure and fracture pressure. In conventional drilling practice, single mud weight exists from drilling unit to TVD (True Vertical Depth) which creates big hydrostatic pressure in bottom hole, moreover, minor changes in mud weight results in big pressure changes proportional to the length of hydrostatic column increase with water depth. On the other hand, DGD allows using two different mud weights to get same bottom hole pressure; low gradient drilling fluid from drilling unit to the sea floor and high gradient drilling fluid form the sea floor to TVD, to decrease the effect of water column on mud hydrostatic pressure in TVD. In this study, a conventionally drilled deep water well was redesigned considering the DGD system and drilled virtually to determine the changes of cost of services and materials on total operation budget to prove the positive impact of system on total operation cost. This study not only proved the technical advantages of the DGD system, but also showed economical impact of the system on total drilling cost, by decreasing around 19%.
-
-
-
A case study for understanding waterflood performance and reservoir connectivity using analytical tools
Authors B. Fernandes, Y. Cabral and E. ArtunUnderstanding waterflood performance and reservoir connectivity is a challenging and critical aspect of reservoir engineering to efficiently employ improved reservoir management strategies. In this paper, application of two commonly used analytical tools for waterflooding evaluation, reciprocal productivity index (RPI) and modified Hall Integral (MHI), is presented for a field that has gone through pattern waterflooding for 10 years. RPI enable to both interpret and understand the performance of active producers in response to the degree of influence by the injectors. By interpreting the behavior of the Hall Integral and the modified Hall Integral it is possible to analyze the individual performance of injectors. Furthermore, both methods can be combined along with the average reservoir pressure variations so as to support the interpretations for understanding performances both producers and injectors.
-
-
-
A Field Application with Liquid Surfactant for Production Optimization
By Ö. SunalLiquid loading in gas wells is a major concern that causes production reduction and shortening of the well life. Liquid loading arises when a gas well is unable to remove the produced liquids from the wellbore. Gas rates below the critical rate are insufficient to remove the liquid and lead to an accumulation in the wellbore which eventually might kill the well. There are various methods to deliquify gas wells, each of which can be implemented as the optimum method in different cases based on the well specifications. Most of these methods can be unsuccessful for highly depleted wells with low reservoir pressures and low flow rates. This study introduces a new field application of deliquification of a gas well in Turkey which is the first successful optimization application in the country through continuous liquid surfactant (foamer) injection. The study focuses on increasing the ultimate recovery of a highly depleted well with intermittent flow due to water buildup issue via unloading the accumulated liquid and producing gas continuously at a stable rate and therefore extending the well life.
-
-
-
Cross-equalization and pre-stack seismic inversion of timelaps land seismic data, Thrace Basin, Turkey
Authors S. Baytok, B. Selek and H. ÖzdemirThis study aims to map undrained gas zones by crossequalization and pre-stack seismic inversion of the base and monitor surveys for sweet spot mapping and discriminating pore fill and pressure changes. 4D land seismic data acquired and used in this study is reasonably in good quality but the repeatability is very poor. Spurious 4D anomalies are present in the data even after parallel processing including deconvolution and pre-stack migration. For land seismic data, this is usually expected but it should be noted that amplitude difference between 4D data is not acceptable, and timelapse difference amplitudes seem not to be reasonable (Figure 1, top panel). As a result, a cross-equalization is required before any attempt of time-lapse data analysis and interpretation. The seismic and inverted acoustic impedance (AI) difference maps of crossequalized time-lapse data showed good agreement with the production data at the producing wells assuming that the changes are due to changes in pore fill only. Possible changes and its effect from pressure decrease due to production need further investigation. The gas production is free of water. It is expected to have no water drive, when the gas in the reservoir is produced the gas-water contact stays at the same level.
-
-
-
Deliquification of Thrace Basin gas wells
More LessThe Thrace basin is located in the European section of NW Turkey. It consists mainly of shallow gas production with a depth of 500 to 1500 meters. These wells exhibit a rapid production decline as rates drop off sharply within the first few months of production. Left unassisted, the production of these wells drops off to unacceptable levels quickly due primarily to liquid loading. In 2012 a project was undertaken to address the liquid loading problem. Candidate wells were selected from the Osmancik, Mezardere, and Teslimkoy formations with the intent of installing plunger lift systems for deliquification. Of the target wells, some had been frac’d and others had not. The expectation was that the fracturing would open up production and that the plunger lift would allow these wells to stay ahead of the liquids. Various types of plungers were used in both continuous flow and conventional plunger lift modes. Automated control options were utilized for auto-optimization and gathering of information via telemetry. The results of the first group of wells showed mixed results. Some showed significant production increases while others merely maintained the production levels and slowed down the production decline. On those wells where the plungers were installed during the steep portion of the decline, the rates continued to drop even after installing artificial lift. An investigation as to the similarities of those showing the best results was done to help identify successful future candidates. Frac sand created an additional problem on several of the wells. Even though the volume of sand had a tendency to decrease after some flow back time, there was still enough sand in some wells to not make plunger lift a viable option. All in all the production was increased significantly. The intent of this paper is to evaluate these wells and help identify further candidates and production results.
-
-
-
Selection Criteria for Water Shut Off Polymer Gel Injection In Carbonate Medium
Authors S. Canbolat and M. ParlaktunaNowadays there remained no giant oil fields has been left undiscovered on shore and maturation of discovered ones have brought difficulties during production. The major one is the higher water production for the petroleum industry, as more reservoirs become mature. Higher water production in oil fields is one of the major difficulties for the petroleum industry, as more reservoirs become mature. Costs of lifting, handling, separation and disposal of large amounts of produced water; environmental concerns about this water; increased corrosion rates; higher tendency for emulsion; and, scale formation are among the main problems due to water production which often decrease the economic life of a well. Therefore, there is a need to reduce excessive water production.
-
-
-
Suudi Arabistan’ın Paleozoyik Petrol Sistemleri (Paleozoic Petroleum Systems Of Saudi Arabia)
By M. ŞenalpGonduvana kıtası üzerinde çökelmiş olan kalın Paleozoyik istifler, 1970 yılında Katar ve İran’da Khuff karbonatları içinde gaz ve Oman da ise petrol rezervlerinin bulunup üretilmesiyle birlikte bütün ülkelerde ilgi odağı olmuştur. Gonduvana kıtası üzerindeki Paleozoyik istifleri, bu kıtanın ekvator ile güney kutbu arasında sürekli olarak göç etmesine bağlı olarak, buzul ortamından kurak karasal ortama ve sığ deniz ortamından derin deniz ortamına kadar değişen çok farklı koşullar altında çökelmiş kırıntılı kayaçlardan oluşmuştur. Karbonat istifleri Geç Permiyen zamanında çökelmeye başlamıştır. Suudi Arabistan’ın Paleozoyik istifleri ilk kez 1987 yılında Riyad’ın güneyinde açılan Hawtah–1 kuyusunda çok hafif petrolün keşfedilmesi ile önem kazanmıştır (Senalp and Al-Duaiji, 1995; 2001; Senalp, 2006). İlk açılan bu keşif kuyusundaki rezervuar, yüksek gözenekli ve geçirimli Permiyen kumtaşları, kaynak kaya ise organik madde yönünden çok zengin olan açık deniz ortamında çökelmiş Erken Silüryen şeylleridir.
-
-
-
Güneydoğu Anadoluda Diyarbakır Kuzeyinde Şaryaj Kuşağının Tektoniği, Mesozoyik Yaşlı Allokton ve Otokton Birimlerin Stratigrafisi
Authors M.A. Gül, M. Mutafçılar, G. Arıkanoğlu and S. SancakÇalışılan alan Güneydoğu Anadolu bölgesinde, Diyarbakır kuzeyinde, Hazro antiklinali, Abdülaziz Dağı, Ergani İlçesi arasında Şaryaj Kuşağı olarak bilinen alanda yer almaktadır. Kuzeyde Orojenik kuşakta Allokton Torid-Anatolid Levhasına ait birimler ile Neotetis’e ait ofiyolit ve ofiyolitli melanj, ile bunlar üzerinde ve bu birimler ile tektonik ilişkili Tersiyer yaşlı birimler bulunmaktadır. Kenar Kıvrım Kuşağı’nda Koçali Karmaşığı, Karadut Karmaşığı, Hezan Grubu ve bunlar üzerinde kuzey alanlarında Eosen ve Miyosen yaşlı denizel birimler çökelmiştir. Kenar kıvrım kuşağı, Kıvrım Kuşağı ve Ön Ülkede Üst Maestriştiyen-Pliyosen yaşlı denizel ve karasal birimler çökelmiş ve Kuvaterner yaşlı bazaltlar yayılmıştır. Kenar Kıvrım Kuşağında açılan kuyularda test edilmiş Paleozoyik yaşlı birimler; gerek Hazro Antiklinali’nde gerekse açılan kuyularda benzer fasiyes özelliğindedirler. Ancak Paleozoyik yaşlı birimler üzerine gelen Mesozoyik yaşlı birimler gerek yaş, gerekse fasiyes yönünden oldukça farklı fasiyeslere sahiptirler. Kenar Kıvrım Kuşağının güney alanları ile Kıvrım Kuşağı ve Ön Ülkenin bir kısmında Mardin Grubu birimleri Paleozoyik yaşlı birimler üzerine açısal uyumsuz gelir. Kenar Kıvrım Kuşağı kuzey alanlarında Üst Jura-Alt Kretase yaşlı neritik karbonatlardan oluşan Latdağı Formasyonu Paleozoyik yaşlı birimler üzerinde açısal uyumsuzdur. Latdağı Formasyonu üzerinde bir çok karbonat çökel evresinden oluşan Mardin Grubu birimleri uyumsuz olarak yer alır. Kazanlı-1 kuyusunda Turoniyen-Santoniyen yaşlı pelajik foraminiferli karbonatların varlığı bu döneme ait çukurlukların kuzey alanlarda gelişmiş olabileceğini göstermektedir. Üst Kampaniyen-Alt Maestriştiyen yaşlı Sayındere Formasyonu ve Kastel Formasyonu tüm yaşlı birimleri açısal uyumsuz olarak örter. Bu birimler üzerine Hezan Grubu, Karadut Karmaşığı ve Koçalı Karmaşığından oluşan alloktonlar tektonik olarak gelirler. Bölge bugünkü konumunu Üst Kretase sonu, Orta Eosen öncesi, Alt Miyosen öncesi ve sonrası ve OrtaÜst Miyosen döneminde gelişen sıkışma tektoniği ve son dönemde gelişen yanal atımlı faylar ile kazanmıştır. Kaynak kaya sorunu bulunmayan bu alandaki yapısal unsurlar, hidrokarbon aramacılığı açısından ikinci bir petrol üretim kuşağı oluşturabilir.
-
-
-
New Comparative Stratigraphy of the Southeast Turkey, Northeast Syria and Northeast Iraq by using belemnite and bivalve species
Authors İ. Hoşgör and İ.Ö. YılmazAll new macro-paleontological samples described below were collected at two localities of Hakkari area (Turkey/Iraq boundary), and Mardin-Mazıdağı area (close to Turkey/Syria boundary). We present here the first section, especially northernmost occurrence known of a Tethyan record of veneriids located close to the Turkey/Syria boundary. The Aphrodina dutrugei (Cocquand, 1862) heterodont bivalve species and monotaxic shell beds which are the focus of this study occurs within the Derdere Formation which form the middle part, Cenomanian interval of the Mardin Group.
-
-
-
Güneydoğu Anadolu (Türkiye) Petrol Sistemi (The Petroleum Systems of Southeast Anatolia (Turkey))
Authors İ. Bahtiyar, İ. Açıkbaş, Ö. Aksu, H. Can and M.G. AydınGüneydoğu Anadolu Türkiye Arap Plakası’nın kuzey ucunda yer almaktadır. Arap Plakası ise Geç Prekambriyenden itibaren tüm Paleozoik boyunca Gondwana kıtasının Protetis ve /veya Paleotetis Okyanuslarına bakan kenarında yer almıştır (Smith vd,1981; Beydoun,1988; Husseini,1989;1990; Scotese&McKreeow,1990; Stampfli,2000). Bölgenin tektonik evrimini ve çökel istifini Arap Plakası ile Anadolu Kıtası’nın biribirine göre göreceli hareketleri kontrol etmektedir. Bu hareketlerin etkisi ile Erken Ordovisiyenden itibaren gelişen Mardin-Kahta Yükselimi Güneydoğu Anadolu’yu iki ayrı basene ayırmıştır. Yükselimin batı-güneybatısı Akçakale Baseni, doğu-kuzeydoğusu ise, Diyarbakır Basenidir (Şekil-1). Devoniyenden itibaren Lavrasya ve Gondwananın yakınlaşıp çarpışmasından kaynaklanan Hersiniyen Orojenezinin etkileri Karboniferde de devam etmiş ve Permiyen başında süper kıta Pangea ortaya çıkmıştır. Hersiniyen Orojenezi tüm bölgede olduğu gibi Güneydoğu Anadoluda da hissedilmiş ve epirojenik hareketlere neden olmuştur (Rigo de Righi&Cortesini, 1964; Sungurlu,1974; Carte&Tunbridge,1992). Devoniyenden itibaren Permiyen sonuna kadar etkili olduğu düşünülen Siirt İli civarında K-G uzanımlı başka bir yükselim bu dönemde oluşmuş ve Diyarbakır basenini Hakkari bölgesinden ayırmıştır (Bozdoğan ve Erten,1990).
-
-
-
The records of ammonite, innoceramus and flowering plant abundance level within the Santonian- Campanian pelagic black shales and marls in the Mardin area, SE Turkey
Authors İ.Ö. Yılmaz and İ. HoşgörThe studied area lies within SE Turkey, and take place on the Arabian Platform. Measured stratigraphic sections cover partly the Sayindere and Kastel Formations cropped out in the vicinity of the Mardin and the Mazidag areas.
-
-
-
Exploration at Miocene Mersin Basin: Outputs of the Preliminary Basin and Petroleum Systems Modeling, Mersin Offshore, Turkey, Mediterranean
Authors E. Kansu, H. Yılmaz, S.Y. Çiftçi, İ.P. Hacıköylü and Y.G. KalanyuvaWithin the neighbourhood of onshore Adana and Mut basins at the north, Cyprus at the south and Missis High at the east, Miocene Mersin Basin, is one of the fronteer offshore basins where Turkish Petroleum Corp. has the exploration rights. In order to investigate the hydrocarbon potential of the Miocene Mersin Basin, a 3D basin model was prepared using 2 off-shore wells which are within the project area and outputs of the 2D seismic interpretations. Other then well data, the regional geology and stratigraphy were used to build the chronostratigraphy of the model which begins at 23.2Ma. Using the 12 horizons derived by the seismic interpretations, paleogeometries were established. Not only the isopach maps of formations but also onshore analogies were used to select the appropriate lithologic constituents of the facies. Since Miocene Mersin Basin is a fronteer basin, there are some uncertainities but keeping those in mind, the model shows enough maturity in certain depths for a possible source rock to generate and expel hydrocarbons. Outputs of the 3D basin model of the fronteer Miocene Mersin Basin shows that it has a potential for hydrocarbon exploration.
-
-
-
İskenderun Körfezi Petrol Sistemi ve Modellemesi
More Lessİskenderun Körfezi, Doğu Akdeniz’in kuzeydoğusunda, XIV. Petrol Arama Bölgesi’nin doğusunda yer almaktadır. Yaklaşık 4000 km2 alana sahiptir. Çalışmanın amacı, üç boyut basen modellemesi yapılarak basen evrimi, petrol sistemi unsurları, hidrokarbon oluşumu, göçü ve kapanlanması konularına bugünkü bilgiler doğrultusunda açıklık getirmektir. Modelleme aşamasında sismik veri kullanılarak yorumlanmış yapı haritaları, batimetri haritası, faylar, çalışma alanı içerisinde açılmış 10 kuyuya ait veriler ve 7 adet sanal kuyuya ait beklenir stratigrafi verileri kullanılmıştır. Kuyu loglarından birimlerin porozite değerleri hesaplanmış, ölçülmüş sıcaklık ve basınçlar, sondaj çamur ağırlıkları ve jeokimya analiz sonuçları değerlendirilerek sonuçlara ulaşılmıştır. Basen, Orta Miyosen döneminde yanal atımlı gerilme rejimiyle gelişmeye başlamış, bölgedeki horst ve grabenler daha çok KD-GB trendindeki normal faylar ile doğrultu atımlı fayların bileşenlerinin sonucu olarak oluşmuştur. Menzelet ve Horu formasyonları eş zaman çökelleri olup, basenin kaynak kayası Menzelet Formasyonu ve rezervuarı Horu kireçtaşlarıdır. Ayrıca Kızıldere Formasyonu içerisine yorumsal olarak rezervuar seviyeler tanımlanmıştır.
-
-
-
Libya Murzuk Baseni Petrolleri ile Türkiye Güneydoğu Anadolu (GDA) Siluriyen Yaşlı Kaynak Kayalardan Türeyen Petrollerin Jeokimyasal Korelasyonu
Authors Y.H. İztan, H. Çorbacıoğlu, A. Canatalı, E.E. Tokoğlu and P. YılmazerLibya Murzuk Baseni’nden alınan dört petrol örneği (L1, L2, L3 and L4) ile Türkiye’nin Güneydoğu Anadolu Bölgesi’nden alınan üç petrol örneğinin (T1, T2, T3) kaynak kaya çökelme ortamları, kaynak kaya litolojileri ve olgunlukları ile her iki grup petrolün birbirleriyle olan benzerlikleri jeokimyasal yöntemler kullanılarak saptanmaya çalışılmıştır.
-